Linear Technology Demo Boards

DC2473A - LTC6419 - Dual Differential Amplifiers / ADC Drivers

Mar 15th 2017
Demonstration circuit 2473A features the LTC®6419 Dual Differential Amplifier/ADC Driver. It incorporates a variety of passive components to support configurations for varied applications. These fully-differential amplifiers accept single-ended or differential input with almost no difference in distortion performance. ...

 

DC2418A-B - LTC4368-2 Demo Board | UV, OV, OC and Reverse Supply Protection with -3mV Reverse ECB

Mar 9th 2017
Demonstration circuit 2418A is intended to demonstrate the performance of the LTC®4368 100V undervoltage (UV), overvoltage (OV), and reverse protection controller with bidirectional circuit breaker. The LTC4368 protects circuits from overcurrent in both directions and from input voltages that may be too high, too low, or ...

 

DC2418A-A - LTC4368-1 Demo Board | UV, OV, OC and Reverse Supply Protection with -50mV Reverse ECB

Mar 9th 2017
Demonstration circuit 2418A is intended to demonstrate the performance of the LTC®4368 100V undervoltage (UV), overvoltage (OV), and reverse protection controller with bidirectional circuit breaker. The LTC4368 protects circuits from overcurrent in both directions and from input voltages that may be too high, too low, or ...

 

DC2588A-A - LTC2387-18 Demo Board | 18-Bit, 15Msps SAR ADC using ADA4899-1 ADC Driver (Requires DC718)

Mar 8th 2017
Demonstration circuit 2588A features the LTC®2387 family driven by a pair of ADA4899-1 driver amplifiers. With up to 15Msps, these differential input, single channel, 18-/16- Bit, serial, high speed successive approximation register (SAR) ADCs are available in a 32-Pin QFN package. The LTC2387 family has an internal 20ppm/°C ...

 

DC2423A-B - LTM9100 Demo Board | Isolated 380V Switch Controller with Telemetry [requires DC590 or DC2026]

Mar 8th 2017
Demonstration circuit 2423A showcases the LTM®9100 Isolated Switch Controller in either a typical 48V application (–A) or in a high voltage 380V application (–B). The board may be configured for either high side or low side operation, dependent on the connection of external supply and load to the banana jacks. ...

 

DC2423A-A - LTM9100 Demo Board | Isolated 48V Switch Controller with Telemetry [requires DC590 or DC2026]

Mar 8th 2017
Demonstration circuit 2423A showcases the LTM®9100 Isolated Switch Controller in either a typical 48V application (–A) or in a high voltage 380V application (–B). The board may be configured for either high side or low side operation, dependent on the connection of external supply and load to the banana jacks. ...

 

DC9018B-B - SmartMesh IP RF Certified Eval/Dev Mote (MMCX antenna connector with 2dBi Dipole antenna)

Mar 3rd 2017
SmartMesh IP Networks are populated by motes, the nodes on the network. Based on the Dust® breakthrough Eterna® technology, the motes are ultralow power, extending battery life to years and many times that of alternative products. In addition to extra long battery life, the motes feature ...

 

DC2274A-B - SmartMesh IP USB Access Point Mote

Mar 3rd 2017
The DC2274A-B USB dongle demo board which serves as an Access Point Mote, connecting a SmartMesh IP™ wireless sensor network with a VManager network manager. VManager is a software-based manager that enables: Large Networks – thousands of nodes Increased Bandwidth through Multiple Access Points Hot ...

 

DC9021B - SmartMesh IP Starter Kit

Mar 3rd 2017
    The DC9021B SmartMesh IP™ Starter Kit provides all the tools for evaluating SmartMesh® network performance with respect to your application needs, including high reliability, ultralow power, scalability and ease of installation. This accelerates device integration and application software ...

 

DC9005B - Eterna QuikEval Adapter

Mar 3rd 2017
The DC9005B Eterna QuikEval Adapter card makes it easy to connect the DC9018B-B SmartMesh IP Evaluation/Development Mote to QuikEval enabled demo boards. Users can program a SmartMesh IP mote (e.g. DC9018B-B) with the SmartMesh IP On-Chip SDK. In the diagram below, the DC9018B-B can act as an SPI or I2C master to ...

 

DC2129A - LTC3119 Demo Board | Sync Buck-Boost, 2.5V ≤ VIN ≤ 18V, VOUT = 5V @ Up to 5A

Feb 24th 2017
Demonstration circuit 2129A features the LTC®3119, an 18V, 5A synchronous buck/boost DC/DC converter. The DC2129A has been designed for an input voltage range of 2.5V to 18V with an output voltage (VOUT) set to 5V. For VIN > 5V the output current can be as high as 5A. The unique 4-switch, single inductor architecture ...

 

DC2111A-B - LTC3774EUHE Demo Board | Sync Buck Controller, 4-Phase (LTC3774 x2), 10V ≤ VIN ≤ 14V, Vout = 1.2V @ 120A

Feb 22nd 2017
Demonstration circuit DC2111A-B features the LTC®3774 in a 4-phase, high output current step-down converter with sub-mΩ DCR sensing. This high performance, high efficiency converter provides 1.2V @ 120A and operates at a switching frequency of 400kHz over an input voltage range of 10V to 14V. The 5mm × 5mm DrMOS ...

 

DC1705C-B - LTC6946-2 Demo Board | Ultralow Noise and Spurious 513MHz to 4.91GHz Integer-N Synthesizer with Integrated VCO (Req DC590 or DC2026)

Feb 22nd 2017
DC1705C features the LTC®6946, an ultralow noise and spurious integer-N frequency synthesizer with integrated VCO. The VCO uses no external components and is internally calibrated without external system support. There are three versions of the DC1705C, one for each version of the LTC6946. The DC1705C-A contains the LTC6946-1, ...

 

DC2390A-A - LTC2500-32 Demo Board | 32-Bit Over-Sampling ADC Multi-Application Demoboard (req ArrowSoCKIT)

Feb 21st 2017
Demonstration circuit 2390A is a general-purpose test platform for prototyping and evaluating some of the key applications for the LTC2500 family of high resolution, oversampling ADCs. Assembly type A includes two LTC®2500-32, 32-bit oversampling ADCs with configurable digital filters, two LTC1668 16-bit, 50Msps DACs, analog ...

 

DC2518A - LTC2975 Demo Board: +/- 12V, +/- 48V Power Supply Management [requires DC1613]

Feb 21st 2017
The DC2518A is a demonstration system for the LTC®2975 Power System Manager that interfaces to various regulators. The board contains all the circuitry needed to use the LTC2975 in a power system and control four power supplies. The four power supplies include linear and switching regulators for the purpose of demonstrating ...

 

DC2222A-A - LTC2500-32 Demo Board | 32-Bit Over-Sampling ADC with Configurable Digital Filter (req DC590, DC2026 or DC890)

Feb 17th 2017
Demonstration circuit 2222A features the LTC2508-32 and LTC2512-24 ADCs. The LTC2508-32 and LTC2512-24 are low power, low noise, high speed, 32-bit/24-bit SAR ADCs with an integrated configurable digital averaging filter that operate from a single 2.5V supply. The following text refers to the LTC2508-32 but applies to both parts, ...

 

DC1812A-B - LTC2944 Demo Board | 60V Battery Gas Gauge (req. DC2026)

Feb 15th 2017
Demonstration circuit 1812A-B features the LTC2944. Demonstration circuit 1812A-C features the LTC2943-1. The LTC2943/LTC2943-1 has an operating range of 3.6V to 20V, while the LTC2944 has an operating range of 3.6V to 60V, making all three devices perfectly suited for multicel battery applications. A precision analog coulomb ...

 

DC2230A-B - LTM4636-1 Demo Board | Buck μModule Regulator with OV/Temp Protection, Stacked Inductor; 4.7V ≤ VIN ≤ 15V, Vout = 1V @ 40A

Feb 15th 2017
Demonstration circuit 2230A-B features the LTM®4636-1EY, a 40A high efficiency, switch mode step-down power μModule® regulator with overtemperature and input/output overvoltage protection. The input voltage range is from 4.7V to 15V. For a 4.7V to 5.5V input voltage range, short PVCC pin to the VIN pin with R8 = R21 ...

 

DC2512A - HSMC Adapter for DC718-Compatible Demo Boards

Feb 14th 2017
Demonstration circuit 2512A is a gasket adapter board that allows DC718-compatible data converter eval boards to interface with FPGA boards that have an HSMC connector, such as the SoCkit Cyclone 5 SoC development board from Arrow Electronics. ...

 

DC2511A - HSMC Adapter for DC890-Compatible Demo Boards

Feb 14th 2017
Demonstration circuit 2511A is a gasket adapter board that allows DC890-compatible data converter eval boards to interface with FPGA boards that have an HSMC connector, such as the SoCkit Cyclone 5 SoC board from Arrow Electronics. ...

 

DC2111A-A - LTC3774EUHE Demo Board | Sync Buck Controller, 4-Phase (LTC3774 x2), 10V ≤ VIN ≤ 14V, Vout = 1.2V @ 90A

Feb 13th 2017
Demonstration circuit DC2111A-A features the LTC®3774 in a 4-phase, high output current step-down converter with sub-mΩ DCR sensing. This high performance converter provides 1.2V @ 90A with N+1 MOSFET failure protection and operates at a switching frequency of 400kHz over an input voltage range of 10V to 14V. The 5mm ...

 

DC2434A - LTC3864 Demo Board | Buck Controller, 12V ≤ VIN ≤ 60V, Vout = 12V @ 5A

Feb 13th 2017
Demonstration circuit 2434A is a high voltage, current mode DC/DC step-down converter featuring the LTC®3864. The board operates from an input range of 6V to 60V and provides a 12V, 5A output when the input exceeds 12V. The PMOSFET architecture allows it to operate seamlessly up to 100% duty cycle and function as a saturated ...

 

DC2073A-H - LTC6906 Silicon Oscillator Demo Board

Feb 13th 2017
DC2073A-H - Demo Board for:LTC6906 - Micropower, 10kHz to 1MHz Resistor Set Oscillator in SOT-23 ...

 

DC765B - LT3479EDE Demo Board | Positive/ Negative Converter (LT3479 x2), Boost: 2.5V ≤ VIN ≤ 4.2V, Vout=7V@600mA, Inverter: 2.5V ≤ VIN ≤ 12V, Vout=-5V@600mA

Feb 9th 2017
Demonstration circuit 765B is a general purpose 1MHz, positive and negative converters featuring the LT3479EDE. The demo circuit demonstrates small size and low component count in a boost circuit and an inverting circuit. The boost converter is set up to convert a 2.5V to 4.2V input to 7V output at 600mA. The inverting circuit ...

 

DC1410A-B - LTC2449 Demo Board | Load Cell Digitizer Application, req DC2026C

Feb 7th 2017
Demonstration circuit 1410A shows a compact, high resolution solution for measuring Wheatstone bridge type sensors for load, pressure, temperature, acceleration, and many other physical quantities. Assembly type B features the LTC2449, an 8-/16-channel, high speed, 24-bit Δ∑ ADC with ten selectable speed/resolution ...

 

DC1410A-A - LTC2498 Demo Board | Load Cell Digitizer Application, req DC2026C

Feb 7th 2017
Demonstration circuit 1410A shows a compact, high resolution solution for measuring Wheatstone bridge type sensors for load, pressure, temperature, acceleration, and many other physical quantities. Assembly type A features the LTC2498, an 8-/16-channel, 24-bit ΔΣ ADC with easy drive inputs. Key DC specifications ...

 

DC2365A-E - LTC2358-16 Demo Board | Buffered Octal, 16-Bit, 200ksps Simultaneous Sampling SAR ADC (req DC590, DC2026 or DC890)

Jan 31st 2017
Demonstration circuit 2365A highlights the LTC®2358 family of buffered input ADCs. The LTC2358/LTC2357/ LTC2353/LTC2333 are low noise, high speed, 16-/18- bit successive approximation register (SAR) ADCs with integrated front end buffers. These ADCs accept a wide common mode range. Pico-amp inputs and high CMRR enable these ...

 

DC1332B-A - LTC2631A-LM12 Demo Board | 12-Bit I2C DAC (2.5V ref, Reset to Mid-Scale), req DC590

Jan 27th 2017
Demonstration circuit 1332B features the LTC®2631, a 12-bit I2C DAC with 1LSB (max) INL error. This device establishes a new benchmark for size and integration of 12-bit DACs and onboard reference. The DC1332B may be connected directly to the target application’s analog signals while using the DC590 USB serial controller ...

 

DC2337A - LT8315EFE Isolated Demo Board | Offline Flyback, 90VAC ≤ VIN ≤ 265VAC, VOUT = 12V @ 0.55A

Jan 27th 2017
Demonstration circuit 2337A is an offline isolated flyback converter featuring LT®8315. The demo board outputs 12V, and maintains tight regulation with a load current from 4mA to 0.55A. It is optimized to operate over a wide AC input voltage range (90VAC to 265VAC, 47Hz to 63Hz). Output voltage accuracy stays within ±5% ...

 

DC536B-A - LTC4211CMS Demoboard | 7A Electronic Circuit Breaker and Hot Swap Controller

Jan 27th 2017
Demonstration circuit 536B is a hot swap controller with multifunction current control featuring the LTC®4211. The DC536B-A is configured to operate with up to 7A load and DC536B-B up to 20A load. ...

 

DC569B - LTC4054ES5-4.2 | Li-Ion Linear Battery Charger, 4.25V ≤ VIN ≤ 10V, 1-Cell @ 450mA/600mA ICHARGE

Jan 26th 2017
Demonstration circuit 569 is a single cell Li-Ion linear charger in a SOT-23. Charge rates as high as 600mA can be achieved due to the LTC®4054’s internal die temperature control loop that prevents excessive PCB heating under worst-case conditions. The user is provided with a control jumper to select between OFF/450mA/600mA ...

 

DC2460A - LTC5566 | 300MHz - 6GHz Dual Programmable Gain Downconverting Mixer (Featuring LTC5566) (Companion Board DC2026C; Linduino Software Optional)

Jan 26th 2017
Demonstration circuit 2460A is optimized for evaluation of the LTC®5566 dual programmable gain downconverting mixer. Each channel incorporates an active mixer and a digital IF VGA with 15.5dB gain control range. The IF gain of each channel is independently programmable through the SPI in 0.5dB steps. Its single-ended RF ...

 

DC2438A - LTM2894 Demo Board | USB uModule Isolator

Jan 26th 2017
Demonstration circuit 2438A is an isolated USB data transceiver featuring the LTM®2894. The demo circuit features an EMI optimized circuit configuration, including an isolated DC-DC converter, and printed circuit board layout. All components for data signaling and isolation are integrated into the LTM2894 using LTC’s ...

 

DC2457A - LT8390 Demo Board | Sync Buck-Boost Controller, 4V ≤ VIN ≤ 60V, VOUT = 12V @ 4A (Fsw=400kHz)

Jan 20th 2017
Demonstration circuit DC2457A is a 12V, 4A, 4-switch synchronous buck-boost regulator featuring low EMI noise and small footprint. It runs at 400kHz switching frequency. Spread spectrum frequency modulation (SSFM) can be turned on with a simple jumper, reducing EMI. DC2457A also comes with other low EMI features including optimized ...

 

DC2539A-A - LT4295/LT4321 Demo Board | PoE++ (51W, 12V/3.9A) PD with Flyback DC/DC and Ideal Diode Bridge

Jan 19th 2017
Demonstration circuit 2539A is an IEEE802.3bt (Draft 2.1) compliant Power over Ethernet (PoE) Powered Device (PD). It features the LT®4295 PD interface and switching regulator controller and the LT4321 PoE ideal diode bridge controller. ...

 

DC2476A-A - LT4295/LT4321 Demo Board | PoE++ (62W/24V/2.7A or 71W/24V/2.4A) PD with Flyback DC/DC and Ideal Diode Bridge

Jan 19th 2017
Demonstration Circuit 2476A is an IEEE 802.3bt (Draft 2.2) compliant power over ethernet (PoE) powered device (PD). It features the LT®4295 PD interface and switching regulator controller and the LT4321 PoE ideal diode bridge controller. ...

 

DC1791A-D - LTM2887-5I Demo Board | I2C uModule Isolator (5.0V Supply)

Jan 19th 2017
Demonstration circuit 1791A is a serial peripheral interface bus (SPI) or inter-IC bus (I2C) μModule isolator with dual adjustable 5V regulators featuring the LTM®2887. The demo circuit features an EMI optimized circuit configuration and printed circuit board layout. All components are integrated into the μModule isolator. ...

 

DC1791A-C - LTM2887-3I Demo Board | I2C uModule Isolator (3.3V Supply)

Jan 19th 2017
Demonstration circuit 1791A is a serial peripheral interface bus (SPI) or inter-IC bus (I2C) μModule isolator with dual adjustable 5V regulators featuring the LTM®2887. The demo circuit features an EMI optimized circuit configuration and printed circuit board layout. All components are integrated into the μModule isolator. ...

 

DC1791A-B - LTM2887-5S Demo Board | SPI uModule Isolator (5.0V Supply)

Jan 19th 2017
Demonstration circuit 1791A is a serial peripheral interface bus (SPI) or inter-IC bus (I2C) μModule isolator with dual adjustable 5V regulators featuring the LTM®2887. The demo circuit features an EMI optimized circuit configuration and printed circuit board layout. All components are integrated into the μModule isolator. ...

 

DC1791A-A - LTM2887-3S Demo Board | SPI uModule Isolator (3.3V Supply)

Jan 19th 2017
Demonstration circuit 1791A is a serial peripheral interface bus (SPI) or inter-IC bus (I2C) μModule isolator with dual adjustable 5V regulators featuring the LTM®2887. The demo circuit features an EMI optimized circuit configuration and printed circuit board layout. All components are integrated into the μModule isolator. ...

 

DC2123B - LT3790 Demo Board | Sync Buck-Boost, 8V ≤ VIN ≤ 56V, Vout = 24V at up to 5A

Jan 18th 2017
The DC2123B is a 60V four-switch synchronous buck-boost controller that demonstrates the high power capability of the LT®3790. The output is 24V and the maximum output current is 5A. The switching frequency is 200kHz and efficiency is as high as 98% for a 24V input. The LT3790 is capable of high power operation. DC2123B ...

 

DC2541A - LTC4279 Demo Board | Single Port PoE/PoE+/LTPoE++ PSE Controller (Up to 123W)

Jan 17th 2017
Demonstration circuit 2541A features the LTC®4279, an autonomous single port Power Sourcing Equipment (PSE) controller for use in IEEE 802.3at Type 1, Type 2 and LTPoE++® compliant Power over Ethernet (PoE) systems. The LTC4279 simplifies IEEE and LTPoE++ PSE implementation, requiring only a 45-57V supply and a small ...

 

DC2487A - LTC6363 Rail-to-Rail SAR ADC Driver Amplifier

Jan 10th 2017
Demonstration circuit 2487A features the LTC®6363 amplifier. The DC2487A is designed to drive the inputs of the DC2290A demo board. The DC2290A features the LTC®2387 18-bit, 15Msps high speed SAR ADC. The linearity and low noise of the LTC6363 make it an ideal candidate to drive the LTC2387 at frequencies up to 100kHz. ...

 

DC2344A - Gleanergy Multi-Source Energy Harvesting Demo Board with Battery Chargers and Life-Extenders for Use with DC2321A Dust Demo Board

Jan 4th 2017
Demonstration circuit 2344A development platform is a versatile Energy Harvesting Demo Board that is capable of accepting solar, thermal, and piezoelectric energy sources or any high impedance AC or DC source. The board contains four independent power circuits consisting of the following EH ICs: LTC3106:  “300mA, ...

 

DC2493A - LTC3892EUH-2 Demo Board | 2-Phase Sync Buck Controller, 16V ≤ VIN ≤ 55V; VOUT = 12V @ 30A

Jan 3rd 2017
Demonstration circuit 2493A is a high output voltage capable, high efficiency synchronous PolyPhase® buck converter featuring the LTC®3892EUH-2. The DC2493A has a wide input voltage range from 16V to 55V, and is capable of delivering up to 30A of output current. The output voltage of the DC2493A is set to 12V, however, ...

 

DC2414A - Un-Populated Demonstration Circuit; Supports 3 Channels of LTC6268 & LTC6268-10/LTC6226X

Jan 3rd 2017
Demonstration Circuit 2414A has layouts for three channels of SOT-23 transimpedance amplifiers. Each of the three layouts applies different techniques achieving various parasitic feedback capacitances (CF). The upper channel, U3, assumes a low Transimpedance gain, has a parasitic CF of 0.1pF, and provides a footprint for an ...

 

DC2071A-C - LTC2374-16 Demo Board | 16-Bit, 2Msps, 8-Channel SAR ADC with 96dB SNR (req DC590, DC2026 or DC890)

Dec 19th 2016
Demonstration circuit 2071A features the LTC®2373 family. The LTC2374/LTC2373/LTC2372 are low noise, high speed, 8-channel, 16/18-bit successive approximation register (SAR) ADCs. The following text refers to the LTC2373-18 but applies to all parts in the family, the only differences being the number of bits and the maximum ...

 

DC2454A - LTC3887EUJ-1/LTC3870EUF-1 Demo Board | Dual Phase PMBus Buck Controller with Slave Controller, 7V ≤ VIN ≤ 14V, 0.8V ≤ VOUT ≤ 1.8V @ 100A

Dec 19th 2016
Demonstration circuit 2454A is a high current, high efficiency, poly-phase synchronous buck converter featuring the LTC®3887EUJ-1, a dual-phase current mode controller, and the LTC3870EUF-1, a dual-phase slave controller. The LTC3887-1 has the PMBus interface and the power system management functions. ...

 

DC2405A - LTM2893 Demo Board | 100MHz SPI uModule Isolator

Dec 16th 2016
Demonstration circuit 2405A shows an LTM®2893 isolating and interfacing an LTC®2328-18. The LTM2893 is a high speed SPI isolator for interfacing read only ADCs with a full complement of control signals. The LTC2328-18 is a low noise, high speed 18-bit successive approximation register (SAR) ADC. Low noise isolated power ...

 

DC2043B - LTC3305EFE Demo Board | Lead Acid Battery Balancer for 2-4 Cells

Dec 15th 2016
Demonstration circuit 2043B is a lead-acid battery balancer featuring the LTC®3305. The LTC3305 balances up to four lead-acid batteries connected in series and incorporates all voltage monitoring, gate drive and fault detection circuitry. The LTC3305 employs an auxiliary battery or an alternative storage means to transfer ...

 

DC1794A - LTM2885 Demo Board | 6.5kV Isolated RS485/RS422 μModule Transceiver + Power

Dec 13th 2016
Demonstration circuit 1794A is an isolated RS485/RS422 μModule® transceiver + power featuring the LTM®2885. The demo circuit is a 6500VRMS galvanically isolated RS485/ RS422 transceiver interface. The demo circuit features an EMI optimized circuit configuration and printed circuit board layout. The demo circuit operates ...

 

DC2047A-A - LT4276B/LT4321 Demo Board | PoE+ (25W, 12V/1.9A) PD with DC/DC, Ideal Diode Bridge and 9V-57V AUX

Dec 13th 2016
Demonstration circuit 2047A-A is an IEEE802.3at compliant Power over Ethernet (PoE) Powered Device (PD) with support for 9-57VDC and 24VAC auxiliary supply input. It features the LT®4276 PD interface and switching regulator controller, the LT4321 PoE ideal diode bridge controller, and the LT4320 ideal diode bridge controller. ...

 

DC2475A-A - LT4295/LT4321 Demo Board | PoE++ (40W, 12V/3A) PD with Flyback DC/DC and Ideal Diode Bridge

Dec 13th 2016
Demonstration circuit 2475A-A is an IEEE802.3bt (Draft 2.0) compliant Power over Ethernet (PoE) powered device (PD). It features the LT®4295 PD interface and switching regulator controller with the LT4321 PoE ideal diode bridge controller. ...

 

DC2581A-A - LTC2341-18 Demo Board | Dual, 18-Bit, 666ksps Differential ±5V Input SoftSpan ADC with Wide Input Common Mode Range (req. DC590, DC2026, DC890)

Dec 12th 2016
Demonstration circuit 2581A shows the proper way to drive the LTC®2341 ADC. The LTC2341 is a low noise, high speed, simultaneous sampling 16-/18-bit successive approximation register (SAR) ADC. The LTC2341 has a flexible SoftSpan™ interface that allows conversion-by-conversion control of the input voltage span on a ...

 

DC2581A-B - LTC2341-16 Demo Board | Dual, 16-Bit, 666ksps Differential ±5V Input SoftSpan ADC with Wide Input Common Mode Range (req. DC590, DC2026, DC890)

Dec 12th 2016
Demonstration circuit 2581A shows the proper way to drive the LTC®2341 ADC. The LTC2341 is a low noise, high speed, simultaneous sampling 16-/18-bit successive approximation register (SAR) ADC. The LTC2341 has a flexible SoftSpan™ interface that allows conversion-by-conversion control of the input voltage span on a ...

 

DC2425A-F - LTC2310-12 Demo Board | 12-Bit, 2Msps True Differential Input Serial SAR ADC (Req DC890)

Dec 8th 2016
Demonstration circuit 2425A features the LTC®2311 family. With up to 5Msps, these differential, single channel, 16-bit, serial, high speed successive approximation register (SAR) ADCs are available in a 16-lead MSOP package. The LTC2311 family has an internal 20ppm/°C maximum drift reference and an SPI-compatible serial ...

 

DC2425A-D - LTC2310-14 Demo Board | 14-Bit, 2Msps True Differential Input Serial SAR ADC (Req DC890)

Dec 8th 2016
Demonstration circuit 2425A features the LTC®2311 family. With up to 5Msps, these differential, single channel, 16-bit, serial, high speed successive approximation register (SAR) ADCs are available in a 16-lead MSOP package. The LTC2311 family has an internal 20ppm/°C maximum drift reference and an SPI-compatible serial ...

 

DC2425A-B - LTC2310-16 Demo Board | 16-Bit, 2Msps True Differential Input Serial SAR ADC (Req DC890)

Dec 8th 2016
Demonstration circuit 2425A features the LTC®2311 family. With up to 5Msps, these differential, single channel, 16-bit, serial, high speed successive approximation register (SAR) ADCs are available in a 16-lead MSOP package. The LTC2311 family has an internal 20ppm/°C maximum drift reference and an SPI-compatible serial ...

 

DC2226A-A - 4-Channel 14-bit 250Msps JESD204B ADC with Clocking [Featuring LTC2123, LTC6951]

Dec 8th 2016
Demonstration Circuit 2226A-A is a reference design for a four-channel, 250Msps ADC system consisting of two LTC®2123, dual 14-bit 250Msps ADCs and a JESD204B Subclass 1 clocking solution based on the LTC6951 Clock Synthesizer with Integrated VCO. Other dash options reserved for future use. No external clock source is required ...

 

DC2230A-A - LTM4636 Demo Board | Buck μModule Regulator, Stacked Inductor, 4.7V ≤ VIN ≤ 15V, Vout = 0.6V to 3.3V @ 40A

Dec 2nd 2016
Demonstration circuit 2230A-A features the LTM®4636EY, a 40A high efficiency, switch mode step-down power μModule® regulator. The input voltage range is from 4.7V to 15V. For input voltage range from 4.7V to 5.5V, short PVCC pin to VIN pin with R8 = R21 = 0Ω and remove R17. The output voltage range is 0.6V to ...

 

DC2479A-B - LTM4650EY-1 Demo Board | Dual Phase Buck μModule Regulator, 4.5V ≤ VIN ≤ 15V, Vout = 0.6V to 1.8V @ 50A

Dec 2nd 2016
Demonstration circuit 2479A-B features the LTM®4650EY-1, the high efficiency, high density, dual 25A, single 50A switch mode step-down power module regulator with external compensation. The input voltage is from 4.5V to 15V. The output voltage is programmable from 0.6V to 1.8V. DC2479A-B is configured as dual-phase, single-output, ...

 

DC2479A-A - LTM4650EY Demo Board | Dual Phase Buck μModule Regulator, 4.5V ≤ VIN ≤ 15V, Vout = 0.6V to 1.8V @ 50A

Dec 2nd 2016
Demonstration circuit 2479A-A features the LTM®4650EY, the high efficiency, high density, dual 25A, single 50A switch mode step-down power module regulator. The input voltage is from 4.5V to 15V. The output voltage is programmable from 0.6V to 1.8V. DC2479A-A is configured as dual-phase, single-output, which can deliver ...

 

DC1959B-A - LTC6948-1 Demo Board | Ultralow Noise and Spurious 373MHz to 3.74GHz Frac-N Synthesizer with Integrated VCO, (Req DC590 or DC2026)

Dec 1st 2016
Demonstration circuit 1959B features the LTC6948, an Ultralow Noise and Spurious Fractional-N Synthesizer with Integrated VCO. ...

 

DC2108A - LTC3897 Demo Board | Sync Boost Controller, 16V ≤ VIN ≤ 55V,Vout = 48V @ 4A to 12A

Nov 30th 2016
Demonstration circuit DC2108 is DC/DC boost converter featuring the LTC®3897 constant frequency current mode boost controller. The DC2108A operates over a 16V to 55V input and provides 4A to 12A of output current as shown in Figure 3. The 160kHz (2 •160kHz at the output) constant frequency operation results in a small ...

 

DC2199B-C - LTC3765EMSE/LTC3766EGN Isolated Demo Board | Forward Converter with Sync Rectification, 36V ≤ VIN ≤ 60V; VOUT = 56V @ 5.4A

Nov 29th 2016
Demonstration circuit 2199B-C is a 300W isolated forward converter with synchronous rectification featuring the LTC3765/LTC3766 chip-set. It produces a regulated 56V, 5.4A output from an input voltage range of 36V to 60V. ...

 

DC1525B-D - LTC2172-14 | 14-Bit, 65Msps, 1.8V Quad Serial ADC, 5MHz < Ain < 170MHz, req DC1371 and DC1075

Nov 29th 2016
LTC2175-14 - 14-Bit, 125Msps Low Power Quad ADCs ...

 

DC2131A - LTC3623 Demo Board | Silent Switcher Sync Buck, 4V ≤ VIN ≤ 15V, Vout = 1V/1.5V/2.5V/3.3V/5V @ ±5A

Nov 29th 2016
Demonstration circuit 2131A is a current mode DC/DC step-down Silent Switcher® buck regulator featuring the LTC®3623. The board operates from an input range of 4V to 15V, and provides ±5A of output current. The output voltage of the demonstration board can be set from 0V to VIN – 0.5V. It operates at 1MHz ...

 

DC1525B-B - LTC2174-14 | 14-Bit, 105Msps, 1.8V Quad Serial ADC, 5MHz < Ain < 170MHz, req DC1371 and DC1075

Nov 29th 2016
LTC2175-14 - 14-Bit, 125Msps Low Power Quad ADCs ...

 

DC2520A-B - LTC2344-16 Demo Board | Quad, 16-Bit, 400ksps Differential ±5V Input SoftSpan ADC with Wide Input Common Mode Range (req. DC590, DC2026, DC890)

Nov 29th 2016
Demonstration circuit 2520A shows the proper way to drive the LTC®2344 ADC. The LTC2344 is a low noise, high speed, simultaneous sampling 16-/18-bit successive approximation register (SAR) ADC. The LTC2344 has a flexible SoftSpan™ interface that allows conversion-by-conversion control of the input voltage span on a ...

 

DC1356A - LTC1645CS8 Demoboard | 2-Supply Hot Swap Controller and Sequencer [5V/5A, 3.3V/7A]

Nov 23rd 2016
Demonstration circuit 1356A is a dual hot swap circuit featuring the LTC®1645 dual-channel hot swap controller/ power sequencer. ...

 

DC2504A - LT8630 Demo Board | Sync Buck, 13V ≤ VIN ≤ 100V, VOUT = 12V @ 600mA

Nov 14th 2016
Demonstration circuit 2504A is a step-down converter featuring LT8630. The LT8630 is a monolithic, variable frequency, current mode synchronous step-down switching regulator. The demo board is designed for 12V output from a 13V to 100V input. The wide input range makes it suitable for regulating power from a variety of sources, ...

 

DC2395A-A - LTC2320-16 Demo Board | Octal, 16-Bit, 1.5Msps/ch Simultaneous Sampling SAR ADC (req DC890)

Nov 10th 2016
Demonstration circuit 2395A features the LTC®2325/ LTC2324/LTC2320 family. With up to 5Msps, these differential, multiple channel, 16-bit, serial, high speed successive approximation register (SAR) ADCs are available in a 52-lead QFN package. Each ADC has an internal 20ppm/°C maximum drift reference and an SPI-compatible ...

 

DC2141A - LTM4647 Demo Board | Buck μModule, 6V ≤ VIN ≤ 15V or 4.7V ≤ VIN ≤ 6V, VOUT = 0.6V to 1.8V @ 30A

Nov 9th 2016
Demonstration circuit 2141A features the LTM®4647EY, a 30A high efficiency, switch mode step-down power μModule regulator. The input voltage range is from 6V to 15V. To use DC2141A for input voltage range from 4.7V to 6V, connect INTVCC to SVIN (change R22 from OPT to 0Ω), DRVCC to VIN (change R21 from 0Ω ...

 

DC2507A - LTC2986 and LTC2986-1 Universal Protected Board (req. DC2531 or DC2608)

Nov 9th 2016
Demonstration circuit DC2507A is a resistive protection network designed to interface the LTC®2986 demonstration boards (DC2508 for LTC2986 or DC2618 for LTC2986-1). The LTC2986 is a pin and software compatible 10-channel version of the 20-channel LTC2983. The LTC2986 includes several new modes enabling external protection/ ...

 

DC2510A - Shield Board for use with DC2321A Dust Demo Board

Nov 3rd 2016
Demonstration circuit DC2510A is a shield board for use with the DC2321A Dust application demo board. This board is designed to allow users to built their own custom application circuits directly on the DC2321A with access to all pins of the LTP5901-IPM Dust mote. ...

 

DC2321A - Dust Energy Harvesting Demo Board with E-Ink Display, designed to connect to the DC2344A or DC2509A

Nov 3rd 2016
Demonstration circuit 2321A is a low power wireless sensor node development platform equipped with an E-ink display for user feedback. The system is capable of monitoring and managing its available energy, logging information from sensors and sharing this data over a wireless network. The board is designed to connect to the ...

 

DC2432A - LT6658 Demo Board | Low Noise, High Current, Precision Reference

Oct 24th 2016
Demonstration circuit 2432A features the LT®6658, a precision 2.5V dual output reference that combines the performance of a low drift low noise reference and a linear regulator. Both outputs are ideal for driving the precision reference inputs of high resolution ADCs and DACs, even with heavy loading while simultaneously ...

 

DC2073B-B - LTC1799 Silicon Oscillator Demo Board

Oct 20th 2016
DC2073B demo board features Linear Technology's SOT23 packaged silicon oscillators. The DC2073B demo board is available in eleven different options; DC2073B-A through DC2073B-K. These eleven options provide for the evaluation of resistor-set oscillator ICs and fixed frequency ICs (Table1). ...

 

DC2138B - LT8301ES5 Isolated Demo Board | No-Opto Flyback, 10V ≤ VIN ≤ 32V, VOUT = 12V @ 0.7A to 1A

Oct 19th 2016
Demonstration circuit 2138B is an isolated flyback converter featuring the LT®8301. This demo circuit outputs 5V from a 10V to 32V input, with a nominal of 24V. The output current capability increases with the input voltage. The standby input current of the demo circuit is less than 950μA (typical) at VIN = 24V. ...

 

DC1989B-C - LTM4676A Demo Board | LTM4676A(x4) Current Shared, PMBus Buck uModule, 4.5V ≤ VIN ≤ 17V, Vout = 0.5V to 4V @ 100A

Oct 18th 2016
Demonstration circuit 1989B-C is a high efficiency, high density, μModule regulator with 4.5V to 17V input range. The output voltage is adjustable from 0.5V to 4V, and it can supply 100A maximum load current. The demo board has four LTM®4676A μModule regulators. The LTM4676A is a dual 13A or single 26A step-down regulator ...