1. Skip to navigation
  2. Skip to content
  3. Skip to sidebar

Linear Technology Circuit Collection

LTC6258 Low Noise Reference Use LT6656 for a Low Current Starting Reference

Aug 30th 2017
The LT6656 is a 1µA precision series voltage reference. Yet with low power comes low drive current capability and higher noise. The LTC6259 can be used as a buffer that follows a filter to enhance the utilization of the LT6656 in low power applications. Figure 5a shows such a configuration. First a very low cutoff frequency ...

Circuit LTspice 

 

LTC6258 Low Power Squarewave - Sinewave Oscillator

Aug 30th 2017
A low power sine wave generator can be derived by driving a square wave into the bandpass filter. A complete schematic is shown in Figure 4a. The LTC6992-1 easily configures as a 50% duty cycle 10kHz square wave, and can drive the relatively benign loading seen in the bandpass filter. Figures 4b and 4c show the LTC6992-1 output ...

Circuit LTspice 

 

LTC6258 LED Driver with Self-Oscillation

Aug 30th 2017
The circuit above combines edge detection with use of the shutdown pin of the LTC6259. R2 and R3 bring in a divided down copy of the supply voltage as a reference into the positive terminal. The op amp forces this voltage on the sense resistor RSENSE in “LED ON” operation. In that sense this circuit is similar to ...

Circuit LTspice 

 

LTC6258 Lower Power LED Driver with Voltage Command

Aug 30th 2017
Figure above shows a voltage controlled LED drive circuit. When VIN is at 0V, the op amp supply current is nominally 20μA. The offset, for example, could be 450µV, appears across R1, inducing a 0.45mA current in the LED. Some applications want a guaranteed zero LED current at VIN = 0, and this is the purpose of R5. ...

Circuit LTspice 

 

LTC2063 Micropower Precision Oxygen Sensor

Jul 27th 2017
This low power precision gas sensor circuit operates in an oxygen level range of 0% to 30%, with a nominal output of 1V in normal atmospheric oxygen concentrations (20.9%) when the gas sensor has been fully initialized. Total active power consumption is less than 2.1μA on a single rail supply. Since ...

Circuit LTspice 

 

LTC2063 RTD Sensor with ±1°C Precision

Jul 27th 2017
This low power platinum resistance temperature detector (RTD) sensor circuit draws only 35μA total supply current on a minimum 2.6V rail, and is accurate to within ±1°C at room temperature, including all error intrinsic to the Vishay PTS Class F0.3 Variant RTD. It covers the temperature ...

Circuit LTspice 

 

LTC7820 High Efficiency 24V to –24V, 10A Voltage Inverter with Hot Swap at Input

Jul 24th 2017
The LTC®7820 is a fixed ratio high voltage high power switched capacitor/charge pump controller. The device includes four N-channel MOSFET gate drivers to drive external power MOSFETs in voltage divider, doubler or inverter configurations. The device achieves a 2:1 stepdown ratio from an input voltage as high as 72V, a 1:2 ...

Circuit 

 

LTC7820 High Efficiency 48V to 12V, 20A Voltage Divider

Jul 24th 2017
The LTC®7820 is a fixed ratio high voltage high power switched capacitor/charge pump controller. The device includes four N-channel MOSFET gate drivers to drive external power MOSFETs in voltage divider, doubler or inverter configurations. The device achieves a 2:1 stepdown ratio from an input voltage as high as 72V, a 1:2 ...

Circuit 

 

LTC7820 High Efficiency 24V to 12V, 15A Voltage Divider with Disconnect FET at Output

Jul 24th 2017
The LTC®7820 is a fixed ratio high voltage high power switched capacitor/charge pump controller. The device includes four N-channel MOSFET gate drivers to drive external power MOSFETs in voltage divider, doubler or inverter configurations. The device achieves a 2:1 stepdown ratio from an input voltage as high as 72V, a 1:2 ...

Circuit 

 

LT6018 Low Noise, High CMRR Instrumentation Amplifier

Jun 14th 2017
The LT®6018 is a 33V precision operational amplifier with excellent noise performance. With 0.1Hz to 10Hz noise of only 30nVP-P, the LT6018 is an outstanding choice for applications where 1/f noise impacts system performance. The LT6018 has excellent DC performance with a maximum offset voltage of 50μV and a maximum offset ...

Circuit LTspice 

 

LT6018 Low Noise Precision Current Monitor

Jun 14th 2017
The LT®6018 is a 33V precision operational amplifier with excellent noise performance. With 0.1Hz to 10Hz noise of only 30nVP-P, the LT6018 is an outstanding choice for applications where 1/f noise impacts system performance. The LT6018 has excellent DC performance with a maximum offset voltage of 50μV and a maximum offset ...

Circuit LTspice 

 

LT1160/LT1162 - 60V Max Supply Referenced DC Motor Half-Bridge Driver

Jun 14th 2017
The LT1160/LT1162 are cost effective half-/full-bridge N-channel power MOSFET drivers. The floating driver can drive the topside N-channel power MOSFETs operating off a high voltage (HV) rail of up to 60V. ...

Circuit LTspice 

 

LT1997-3 - Single Supply Current Sense

Jun 14th 2017
Sense resistors R1 converts a current into a voltage. This voltage is buffered (gain of 1) from the input to the output in this amplifier. V1 tests the circuit for response to common mode variation. A simulation will show that the output voltage variation due to the common mode voltage V1 is very small.     The ...

Circuit LTspice 

 

LT1997-3 - Conversion of Single Ended Pulse To Differential Output

Jun 14th 2017
This circuit combines the LT®1997-3 with a high speed amplifier to convert a single-ended signal to differential with a common-mode offset. Extra compensation capacitors C1 and C2 help to shape the final response. Taking higher gain from the LT1997-3 will eliminate the need for these capacitors.     The LT1997-3 ...

Circuit LTspice 

 

LTC6261 Audio Headphones Bridge Driver

May 22nd 2017
The LTC®6261/LTC6262/LTC6263 are single/dual/quad operational amplifiers with low noise, low power, low supply voltage, and rail-to-rail inputs and outputs. They are unity gain stable with capacitive loads up to 1nF. They feature 30MHz gain-bandwidth product, 7V/μs slew rate while consuming only 240μA of supply current ...

Circuit LTspice 

 

LT8310/LT1431 92W Isolated Forward Converter with Opto Feedback; VIN = 48V, VOUT = 54V@1.7A

George Qian - Senior Applications Engineer Mar 29th 2017
The LT8310 is a constant-frequency resonant reset forward converter controller with a low side N-channel MOSFET gate driver. The LT8310 has a wide input voltage range from 6V to 100V. Its switching frequency can be programed from 100kHz to 500kHz to optimize efficiency, performance or external component size. The LT8310’s ...

Blog Post Circuit LTspice 

 

LT4320 LT4320 Ideal Diode Bridge

Jan 27th 2017
The LT®4320/LT4320-1 are ideal diode bridge controllers that drive four N-channel MOSFETs, supporting voltage rectification from DC to 600Hz typical. By maximizing available voltage and reducing power dissipation (see thermograph comparison below), the ideal diode bridge simplifies power supply design and reduces power supply ...

Circuit 

 

LT8315 12V High Input Voltage Isolated Flyback Converter

Jan 19th 2017
The LT®8315 is a high voltage flyback converter with integrated 630V/300mA switch. No opto-isolator is needed for regulation. The device samples the output voltage from the isolated flyback waveform appearing across a third winding on the transformer. Quasi-resonant boundary mode operation improves load regulation, reduces ...

Circuit 

 

LT8315 Wide Input Range Non-Isolated 12V Buck Converter

Jan 19th 2017
The LT®8315 is a high voltage flyback converter with integrated 630V/300mA switch. No opto-isolator is needed for regulation. The device samples the output voltage from the isolated flyback waveform appearing across a third winding on the transformer. Quasi-resonant boundary mode operation improves load regulation, reduces ...

Circuit 

 

LT8315 83% Efficiency 5V/1.5A Isolated Flyback Converter

Jan 19th 2017
The LT®8315 is a high voltage flyback converter with integrated 630V/300mA switch. No opto-isolator is needed for regulation. The device samples the output voltage from the isolated flyback waveform appearing across a third winding on the transformer. Quasi-resonant boundary mode operation improves load regulation, reduces ...

Circuit 

 

LT8315 85% Efficient Universal Input Offline Power Supply

Jan 19th 2017
The LT®8315 is a high voltage flyback converter with integrated 630V/300mA switch. No opto-isolator is needed for regulation. The device samples the output voltage from the isolated flyback waveform appearing across a third winding on the transformer. Quasi-resonant boundary mode operation improves load regulation, reduces ...

Circuit 

 

LTC3119 3.3V,1.5MHz Wide Input Regulator

Jan 18th 2017
The LTC®3119 is a high efficiency 18V monolithic buck-boost converter that can deliver up to 5A of continuous output current. Extensive feature integration and very low resistance internal power switches minimize the total solution footprint for even the most demanding applications. A proprietary 4-switch PWM architecture ...

Circuit 

 

LTC3119 5V, 2MHz Wide Input Regulator

Jan 18th 2017
The LTC®3119 is a high efficiency 18V monolithic buck-boost converter that can deliver up to 5A of continuous output current. Extensive feature integration and very low resistance internal power switches minimize the total solution footprint for even the most demanding applications. A proprietary 4-switch PWM architecture ...

Circuit 

 

LTC3119 12V, 2MHz Wide Input Regulator

Jan 18th 2017
The LTC®3119 is a high efficiency 18V monolithic buck-boost converter that can deliver up to 5A of continuous output current. Extensive feature integration and very low resistance internal power switches minimize the total solution footprint for even the most demanding applications. A proprietary 4-switch PWM architecture ...

Circuit 

 

LTC3119 12V, 750kHz Regulator with Input Supply Rundown

Jan 18th 2017
The LTC®3119 is a high efficiency 18V monolithic buck-boost converter that can deliver up to 5A of continuous output current. Extensive feature integration and very low resistance internal power switches minimize the total solution footprint for even the most demanding applications. A proprietary 4-switch PWM architecture ...

Circuit 

 

LTC3119 Photovoltaic Panel Input Lead-Acid Charger with Temperature Correction (1MHz)

Jan 18th 2017
The LTC®3119 is a high efficiency 18V monolithic buck-boost converter that can deliver up to 5A of continuous output current. Extensive feature integration and very low resistance internal power switches minimize the total solution footprint for even the most demanding applications. A proprietary 4-switch PWM architecture ...

Circuit 

 

LT8630 –15V, 300mA Step-Down Converter

Jan 17th 2017
The LT®8630 is a current mode PWM step-down DC/DC converter with internal synchronous switches that provide current for output loads up to 0.6A. The wide input range of 3V to 100V makes the LT8630 suitable for regulating power from a wide variety of sources, including automotive and industrial systems and 36V to 72V telecom ...

Circuit 

 

LT8630 High Efficiency 100Vin, 12Vout Step-Down Converter

Jan 17th 2017
The LT®8630 is a current mode PWM step-down DC/DC converter with internal synchronous switches that provide current for output loads up to 0.6A. The wide input range of 3V to 100V makes the LT8630 suitable for regulating power from a wide variety of sources, including automotive and industrial systems and 36V to 72V telecom ...

Circuit 

 

LT8630 100Vin, 28Vout Step-Down Converter

Jan 17th 2017
The LT®8630 is a current mode PWM step-down DC/DC converter with internal synchronous switches that provide current for output loads up to 0.6A. The wide input range of 3V to 100V makes the LT8630 suitable for regulating power from a wide variety of sources, including automotive and industrial systems and 36V to 72V telecom ...

Circuit 

 

LT8630 6.5V to 100Vin, 5Vout/0.6A Step-Down Converter

Jan 17th 2017
The LT®8630 is a current mode PWM step-down DC/DC converter with internal synchronous switches that provide current for output loads up to 0.6A. The wide input range of 3V to 100V makes the LT8630 suitable for regulating power from a wide variety of sources, including automotive and industrial systems and 36V to 72V telecom ...

Circuit 

 

LTM4647 Typical 6V to 15V Input 1.0V at 30A Output Design

Jan 17th 2017
The LTM®4647 is a complete 30A output switching mode step-down DC/DC μModule® (power module) regulator. Included in the package are the switching controller, power FETs, inductor and all supporting components. Operating over an input voltage range of 4.7V to 15V, the LTM4647 supports an output voltage range of 0.6V ...

Circuit 

 

LTM4647 Typical 4.7V to 5.5V Input 1.2V at 30A Output Design

Jan 17th 2017
The LTM®4647 is a complete 30A output switching mode step-down DC/DC μModule® (power module) regulator. Included in the package are the switching controller, power FETs, inductor and all supporting components. Operating over an input voltage range of 4.7V to 15V, the LTM4647 supports an output voltage range of 0.6V ...

Circuit 

 

LTM4647 6V to 15V Input, 1.0V Output at 60A

Jan 17th 2017
The LTM®4647 is a complete 30A output switching mode step-down DC/DC μModule® (power module) regulator. Included in the package are the switching controller, power FETs, inductor and all supporting components. Operating over an input voltage range of 4.7V to 15V, the LTM4647 supports an output voltage range of 0.6V ...

Circuit 

 

LTM4647 6V to 15V Input, 1.0V and 1.2V Output with Tracking

Jan 17th 2017
The LTM®4647 is a complete 30A output switching mode step-down DC/DC μModule® (power module) regulator. Included in the package are the switching controller, power FETs, inductor and all supporting components. Operating over an input voltage range of 4.7V to 15V, the LTM4647 supports an output voltage range of 0.6V ...

Circuit 

 

LTM4647 3-Phase 1V at 90A Design with Extra 1 Phase 30A Redundancy

Jan 17th 2017
The LTM®4647 is a complete 30A output switching mode step-down DC/DC μModule® (power module) regulator. Included in the package are the switching controller, power FETs, inductor and all supporting components. Operating over an input voltage range of 4.7V to 15V, the LTM4647 supports an output voltage range of 0.6V ...

Circuit 

 

LTM4647 4-Phase 6-15Vin, 1Vout at 120A Step Down uModule Design

Jan 17th 2017
The LTM®4647 is a complete 30A output switching mode step-down DC/DC μModule® (power module) regulator. Included in the package are the switching controller, power FETs, inductor and all supporting components. Operating over an input voltage range of 4.7V to 15V, the LTM4647 supports an output voltage range of 0.6V ...

Circuit 

 

LTC3897 High Efficiency 2-Phase 24V Boost Converter with In-Rush Current Control, Overcurrent Protection, Input Voltage Surge Protection and Reverse Input Protection

Jan 17th 2017
The LTC®3897 is a synchronous boost DC/DC controller with surge stopper and ideal diode controller. ...

Circuit 

 

LTC3897 High Efficiency 2-Phase 48V Boost Converter with Reverse Input Protection (Surge Stopper Controller Not Used)

Jan 17th 2017
The LTC®3897 is a synchronous boost DC/DC controller with surge stopper and ideal diode controller. ...

Circuit 

 

LTC3897 High Efficiency 2-Phase 48V Boost Converter with Overcurrent Protection (Ideal Diode and Surge Stopper Controllers at the Output)

Jan 17th 2017
The LTC®3897 is a synchronous boost DC/DC controller with surge stopper and ideal diode controller. ...

Circuit 

 

LTC3897 Nonsynchronous 107V/1.5A 2-Phase Boost Converter with In-Rush Current Control, Overcurrent Protection, Input Voltage Surge Protection and Reverse Input Protection

Jan 17th 2017
The LTC®3897 is a synchronous boost DC/DC controller with surge stopper and ideal diode controller. ...

Circuit 

 

LTC6261 Second Order Bessel Filter

Jan 17th 2017
The LTC®6261/LTC6262/LTC6263 are single/dual/quad operational amplifiers with low noise, low power, low supply voltage, and rail-to-rail inputs and outputs. They are unity gain stable with capacitive loads up to 1nF. They feature 30MHz gain-bandwidth product, 7V/μs slew rate while consuming only 240μA of supply current ...

Circuit LTspice 

 

LTC6261 Third Order Butterworth Filter

Jan 17th 2017
The LTC®6261/LTC6262/LTC6263 are single/dual/quad operational amplifiers with low noise, low power, low supply voltage, and rail-to-rail inputs and outputs. They are unity gain stable with capacitive loads up to 1nF. They feature 30MHz gain-bandwidth product, 7V/μs slew rate while consuming only 240μA of supply current ...

Circuit LTspice 

 

LTM4647 4 Phase 1V at 120A Design

Nov 17th 2016
The LTM®4647 is a complete 30A output switching mode step-down DC/DC μModule® (power module) regulator. Included in the package are the switching controller, power FETs, inductor and all supporting components. Operating over an input voltage range of 4.7V to 15V, the LTM4647 supports an output voltage range of 0.6V ...

Circuit 

 

Hybrid Wide Dimming Ratio Linear LED Current Controller Using LT8614 & LT3083/LT6015

Tom Mosteller - Field Applications Engineer Oct 17th 2016
Many applications for LED illumination require wide dimming ratios. This can be accomplished simply via an adjustable current source as show below.  The current source can be varied by a number of different means, and a large LED current range can be achieved. The primary problem with this technique is that the power dissipation ...

Blog Post Circuit LTspice 

 

LT3598 LED Driver for 30 White LEDs with 60mA Each String

Oct 5th 2016
The LT3598 is a fixed frequency step-up DC/DC converter designed to drive up to six strings of LEDs at an output voltage up to 44V. LED dimming can be achieved with analog dimming on the CTRL pin, and with pulse width modulation dimming on the PWM pin. The LT3598 accurately regulates LED current even when the input voltage is ...

Circuit 

 

LT3598 Auto Battery Powered Driver for 20 LEDs with 90mA Each String

Oct 5th 2016
The LT3598 is a fixed frequency step-up DC/DC converter designed to drive up to six strings of LEDs at an output voltage up to 44V. LED dimming can be achieved with analog dimming on the CTRL pin, and with pulse width modulation dimming on the PWM pin. The LT3598 accurately regulates LED current even when the input voltage is ...

Circuit 

 

LT3598 2MHz LED Driver for 20 White LEDs

Oct 5th 2016
The LT3598 is a fixed frequency step-up DC/DC converter designed to drive up to six strings of LEDs at an output voltage up to 44V. LED dimming can be achieved with analog dimming on the CTRL pin, and with pulse width modulation dimming on the PWM pin. The LT3598 accurately regulates LED current even when the input voltage is ...

Circuit 

 

LT3598 1 MHz LED Driver for 36 White LEDs

Oct 5th 2016
The LT3598 is a fixed frequency step-up DC/DC converter designed to drive up to six strings of LEDs at an output voltage up to 44V. LED dimming can be achieved with analog dimming on the CTRL pin, and with pulse width modulation dimming on the PWM pin. The LT3598 accurately regulates LED current even when the input voltage is ...

Circuit 

 

LT3598 90% Efficient LED Driver for 60 White LEDs

Oct 5th 2016
The LT3598 is a fixed frequency step-up DC/DC converter designed to drive up to six strings of LEDs at an output voltage up to 44V. LED dimming can be achieved with analog dimming on the CTRL pin, and with pulse width modulation dimming on the PWM pin. The LT3598 accurately regulates LED current even when the input voltage is ...

Circuit 

 

LT3591 24V to Four White LEDs at 100mA

Oct 5th 2016
The LT3591 is a fixed frequency step-up DC/DC converter specifi cally designed to drive up to ten white LEDs in series from a Li-Ion cell. Series connection of the LEDs provides identical LED currents resulting in uniform brightness and eliminating the need for ballast resistors. The device features a unique high side LED current ...

Circuit 

 

LT3591 Li-Ion Driver for Seven White LEDs

Oct 5th 2016
The LT3591 is a fixed frequency step-up DC/DC converter specifi cally designed to drive up to ten white LEDs in series from a Li-Ion cell. Series connection of the LEDs provides identical LED currents resulting in uniform brightness and eliminating the need for ballast resistors. The device features a unique high side LED current ...

Circuit 

 

LT3591 Li-Ion Driver for Nine White LEDs

Oct 5th 2016
The LT3591 is a fixed frequency step-up DC/DC converter specifi cally designed to drive up to ten white LEDs in series from a Li-Ion cell. Series connection of the LEDs provides identical LED currents resulting in uniform brightness and eliminating the need for ballast resistors. The device features a unique high side LED current ...

Circuit 

 

Op Amp Precision Positive & Negative Clipper using LT6015/LT6016/LT6017

Tom Mosteller - Field Applications Engineer
Aaron Schultz - Applications Manager Signal Conditioning
Oct 3rd 2016
It can be a challenge to match the voltage range of an analog signal to the input range of an analog to digital converter (ADC). Exceeding the ADC’s input range will give an incorrect reading, and if the input goes far enough beyond the power supply rails substrate currents can flow into the ADC which can cause latch up ...

Blog Post Circuit LTspice 

 

LT3759 Wide Vin, 48V @ >100mA Output Boost Converter that Works Down to 1.6V

Christopher Jarboe - Associate Applications Engineer Oct 3rd 2016
The LT®3759 is a wide input range, current mode, DC/DC controller which is capable of regulating either positive or negative output voltages from a single feedback pin. It can be configured as a boost, SEPIC or inverting converter. An internal LDO regulator draws power from VIN or DRIVE to provide up to a 4.75V supply for ...

Blog Post Circuit LTspice 

 

LTC3723-1 130W Isolated Push-Pull Converter for PoE Applications with 93.5% Peak Efficiency

Jeoffrey (Zijian) Wang - Applications Engineer Oct 3rd 2016
This solution is a non-synchronous isolated push-pull converter designed for PoE applications, which can generate a 50V/2.6A output from a 34-38V (36V typical) input voltage range. A 93.5% peak efficiency is achieved for the whole isolated converter and the total solution can be fit into 1/8 brick footprint (2.3” x 0.9”) ...

Circuit LTspice 

 

LTC3649 High Voltage Monolothic Synchronous Buck Regulator with Output Voltage Control

Victor Khasiev - Applications Engineer
Gabino Alonso - Strategic Marketing Engineer
Sep 26th 2016
In many industrial, computer and monitor application is very important to control output voltage "on the fly", during the system operation. LTC®3649 features simple and reliable way to control output by means of low power signal voltage applied to Iset pin. However, this pin can not be left floating, voltage potential must ...

Circuit LTspice 

 

Single-Ended to Differential Driver Circuit for the LTC2387-18 SAR ADC

Doug Stuetzle - Senior Analog Applications Engineer Sep 26th 2016
The LTC®2387-18 is a 15Msps, highly linear, low-noise SAR converter with differential inputs. The combination of excellent linearity and wide dynamic range makes this ADC ideal for high speed imaging and instrumentation applications. No-latency operation provides a unique solution for high speed control loop applications. ...

Blog Post Circuit LTspice 

 

LT3045 500mA, Ultralow Noise, Ultrahigh PSRR Linear Regulator

Sep 21st 2016
The LT®3045 is a high performance low dropout linear regulator featuring LTC’s ultralow noise and ultrahigh PSRR architecture for powering noise sensitive applications. Designed as a precision current reference followed by a high performance voltage buffer, the LT3045 can be easily paralleled to further reduce noise, ...

Circuit 

 

Paralleling Multiple LT3045s for 2A Output Current

Sep 21st 2016
The LT®3045 is a high performance low dropout linear regulator featuring LTC’s ultralow noise and ultrahigh PSRR architecture for powering noise sensitive applications. Designed as a precision current reference followed by a high performance voltage buffer, the LT3045 can be easily paralleled to further reduce noise, ...

Circuit 

 

LT3045 Parallel Devices For 5Vin to 3.3Vout @ 1A With Ultralow Noise

Sep 21st 2016
The LT®3045 is a high performance low dropout linear regulator featuring LTC’s ultralow noise and ultrahigh PSRR architecture for powering noise sensitive applications. Designed as a precision current reference followed by a high performance voltage buffer, the LT3045 can be easily paralleled to further reduce noise, ...

Circuit 

 

LTC3126 5V, 2MHz Step-Down Converter with Dual Inputs

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LTC3126 12V, 2MHz Step-Down Converter with Dual Inputs

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LTC3126 1.8V, 2MHz Step-Down Converter with Dual Inputs

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LTC3126 3.3V, 2MHz Step-Down Converter with Dual Inputs

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LTC3126 3.3V Supply with 200ms Transient Ride-Through Capability

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LT3080 Low Dropout Voltage LED Driver

Sep 15th 2016
The LT3080 is a 1.1A low dropout linear regulator that can be paralleled to increase output current or spread heat in surface mounted boards. Architected as a precision current source and voltage follower allows this new regulator to be used in many applications requiring high current, adjustability to zero, and no heat sink. ...

Circuit 

 

LT3090 5V to +/-2.5V Low Noise Power Supply

Sep 15th 2016
The LT®3090 is a 600mA, low dropout negative linear regulator that is easily parallelable to increase output current or spread heat on surface mounted boards. Designed with a precision current reference followed by a high performance rail-to-rail voltage buffer, this regulator finds use in applications requiring precision ...

Circuit 

 

LT3090 Two-Terminal Current Source

Sep 15th 2016
The LT®3090 is a 600mA, low dropout negative linear regulator that is easily parallelable to increase output current or spread heat on surface mounted boards. Designed with a precision current reference followed by a high performance rail-to-rail voltage buffer, this regulator finds use in applications requiring precision ...

Circuit 

 

LT3090 500mA LED Driver with Grounded LED Tab (Heatsink)

Sep 15th 2016
The LT®3090 is a 600mA, low dropout negative linear regulator that is easily parallelable to increase output current or spread heat on surface mounted boards. Designed with a precision current reference followed by a high performance rail-to-rail voltage buffer, this regulator finds use in applications requiring precision ...

Circuit 

 

LT3065 LED Driver/Current Source

Sep 15th 2016
The LT®3065 Series are micropower, low noise, low dropout voltage (LDO) linear regulators that operate over a 1.8V to 45V input voltage range. The devices supply 500mA of output current with a typical dropout voltage of 300mV. A single external capacitor provides programmable low noise reference performance and output soft-start ...

Circuit 

 

LT3085 Low Voltage, High Current Adjustable High Efficiency Regulator

Sep 15th 2016
The LT3085 is a 500mA low dropout linear regulator that can be paralleled to increase output current or spread heat on surface mounted boards. Designed as a precision current source and voltage follower, this new regulator finds use in many applications requiring high current, adjustability to zero, and no heat sink. The device ...

Circuit 

 

LT3085 Low Dropout Voltage LED Driver

Sep 15th 2016
The LT3085 is a 500mA low dropout linear regulator that can be paralleled to increase output current or spread heat on surface mounted boards. Designed as a precision current source and voltage follower, this new regulator finds use in many applications requiring high current, adjustability to zero, and no heat sink. The device ...

Circuit 

 

LT3085 Adjustable High Efficiency Regulator

Sep 15th 2016
The LT3085 is a 500mA low dropout linear regulator that can be paralleled to increase output current or spread heat on surface mounted boards. Designed as a precision current source and voltage follower, this new regulator finds use in many applications requiring high current, adjustability to zero, and no heat sink. The device ...

Circuit 

 

LT3517 Buck Mode 1A LED Driver

Sep 13th 2016
The LT3517 is a current mode DC/DC converter with an internal 1.5A, 45V switch specifically designed to drive LEDs. The LT3517 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3517 350mA, 5V to 12V Boost Converter with Accurate Input Current Limit

Sep 13th 2016
The LT3517 is a current mode DC/DC converter with an internal 1.5A, 45V switch specifically designed to drive LEDs. The LT3517 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3517 Low Side current Sensing Load Dump Protected Buck-Boost Mode LED Driver

Sep 13th 2016
The LT3517 is a current mode DC/DC converter with an internal 1.5A, 45V switch specifically designed to drive LEDs. The LT3517 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3517 Boost 100mA LED Driver with LED Open Protection

Sep 13th 2016
The LT3517 is a current mode DC/DC converter with an internal 1.5A, 45V switch specifically designed to drive LEDs. The LT3517 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3517 5.5V SEPIC Convener with Short-Circuit Protection

Sep 13th 2016
The LT3517 is a current mode DC/DC converter with an internal 1.5A, 45V switch specifically designed to drive LEDs. The LT3517 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3465 Li-Ion to Five White LEDs

Sep 12th 2016
The LT3465/LT3465A are step-up DC/DC converters designed to drive up to six LEDs in series from a Li-Ion cell. Series connection of the LEDs provides identical LED currents and eliminates the need for ballast resistors. These devices integrate the Schottky diode required externally on competing devices. Additional features include ...

Circuit 

 

LT3465 Li-Ion to Six White LEDs

Sep 12th 2016
The LT3465/LT3465A are step-up DC/DC converters designed to drive up to six LEDs in series from a Li-Ion cell. Series connection of the LEDs provides identical LED currents and eliminates the need for ballast resistors. These devices integrate the Schottky diode required externally on competing devices. Additional features include ...

Circuit 

 

Too many results please adjust your filters