1. Skip to navigation
  2. Skip to content
  3. Skip to sidebar

Solutions Search - Series Voltage References

Reference Filter Increases 32-Bit ADC SNR by 6dB

Guy Hoover - Applications Engineer Sep 26th 2017
Design Note DN568: Introduction Attaining optimal SNR performance from an ADC isn’t just a matter of providing a low noise signal to the ADC’s input. Providing a low noise reference voltage is just as important. While reference noise has no effect at zero-scale, at full-scale any noise on the reference will be visible ...

Blog Post 

 

DC2542A - LTC2358-18, LTM2893, ADA4522-1, LT6658 Demo Board | Isolated Industrial Data Acquisition Board (req ArrowSoCkit)

Sep 15th 2017
Demonstration circuit 2542A is a reference design for robust industrial data acquisition applications based on the LTC2358-18. The LTC2358-18 is capable of high voltage measurements with a large input common range; however, the DC2542A implements input protection that allows up to 400V of continuous input protection. Combined ...

Demo Board LinearLabTools 

 

LTC6258 Low Noise Reference Use LT6656 for a Low Current Starting Reference

Aug 30th 2017
The LT6656 is a 1µA precision series voltage reference. Yet with low power comes low drive current capability and higher noise. The LTC6259 can be used as a buffer that follows a filter to enhance the utilization of the LT6656 in low power applications. Figure 5a shows such a configuration. First a very low cutoff frequency ...

Circuit LTspice 

 

DC2369A - DC2369A Low Power Wireless Current Sense

Aug 30th 2017
The DC2369A demo circuit is a reference design that implements a wireless current sense solution using Analog Device's low power integrated circuits. The only external connection needed is the current to be measured, allowing this circuit to be inserted at any voltage level or isolation level. The design combines components ...

Demo Board 

 

LTC2063 RTD Sensor with ±1°C Precision

Jul 27th 2017
This low power platinum resistance temperature detector (RTD) sensor circuit draws only 35μA total supply current on a minimum 2.6V rail, and is accurate to within ±1°C at room temperature, including all error intrinsic to the Vishay PTS Class F0.3 Variant RTD. It covers the temperature ...

Circuit LTspice 

 

Wireless Current Sense Circuit Floats with Sense Resistor

Kris Lokere - Strategic Applications Manager Apr 25th 2017
Introduction Measuring the current that flows through a sense resistor seems easy. Amplify the voltage, read it with an ADC, and now you know what the current is. But it gets more difficult if the sense resistor itself sits at a voltage that is very different from system ground. Typical solutions bridge that voltage difference ...

Blog Post 

 

Precision Voltage Reference Drives Up to 200mA, Achieves 0.1ppm/mA Load Regulation & 10ppm/°C Drift

Nov 3rd 2016
Dual Output, High Current, Low Noise,Precision Voltage Reference MILPITAS, CA – November 3, 2016 – Linear Technology announces the LT6658, a precision voltage reference that incorporates two high current output buffers. Based on a 2.5V bandgap voltage reference, each output can be separately configured for any voltage ...

Press Release 

 

Precision Dual Output, High Current, Low Noise, Low Drift Reference

Michael B. Anderson - Senior IC Design Engineer Nov 1st 2016
Precision and mixed signal applications usually require a voltage reference and at times several regulators or LDOs to support the analog circuitry. Separate regulators isolate the analog supply, digital supply and the voltage reference. The voltage reference supports the reference inputs of DACs and ADCs, and other devices ...

Video 

 

DC2432A - LT6658 Demo Board | Low Noise, High Current, Precision Reference

Oct 24th 2016
Demonstration circuit 2432B features the LT®6658, a precision dual output reference that combines the performance of a low drift low noise reference and a linear regulator. Demonstration circuits are available with 1.25V, 2.5V, 3.0V, 3.3V, 4.096V and 5V output option parts. Both outputs are ideal for driving the precision ...

Demo Board 

 

Single-Ended to Differential Driver Circuit for the LTC2387-18 SAR ADC

Doug Stuetzle - Senior Analog Applications Engineer Sep 26th 2016
The LTC®2387-18 is a 15Msps, highly linear, low-noise SAR converter with differential inputs. The combination of excellent linearity and wide dynamic range makes this ADC ideal for high speed imaging and instrumentation applications. No-latency operation provides a unique solution for high speed control loop applications. ...

Blog Post Circuit LTspice 

 

Build a Precision Low Noise 5A Power Supply

Michael B. Anderson - Senior IC Design Engineer Sep 6th 2016
The LT6658-2.5V voltage reference has the specifications of a precision reference with dual outputs capable of 150mA and 50mA. This unprecedented combination of precision and power allows the unique ability to create a very precise high-current power supply with load regulation of less than 12ppm/A. Only a few additional components ...

Blog Post 

 

Common Questions About the LTC2668 Family of 16bit VOUT DACs

Mark Thoren - Staff Scientist
Chad Steward - Design Manager
Noe Quintero - Application Engineer
Apr 19th 2016
The LTC2668-16 packs 16, 16-bit high performance Digital to Analog converters (DACs) into a tiny, 6x6mm QFN package, with 8 and 4 channel versions in a 5x5 QFN, and 12-bit versions for lower resolution applications. A general purpose DAC such as this finds its way into a myriad of diverse applications, and tends to generate ...

Blog Post 

 

Voltage Reference: Performance Plus Features

Brendan Whelan - Design Manager Mar 28th 2016
Demand for higher performance in mixed-signal circuits requires ever-better voltage references. But the highest-performance references of yesterday aren’t suitable, as they are generally simple products with few additional features. With the development of high-performance bandgap references, plus improvements in process ...

Video 

 

Industry's Lowest Drift Bandgap Voltage Reference Features 1.5ppm/°C Max & 0.5ppmP-P of Noise

Oct 19th 2015
MILPITAS, CA - October 19, 2015 - Linear Technology announces the LT6657, a family of ultra-stable bandgap voltage references that exhibits less than 1.5ppm/°C of temperature drift. Reinforcing this groundbreaking performance, the LT6657 has only 0.5ppmp-p of low frequency noise, less than 30ppm of long term drift and 35ppm ...

Press Release 

 

DC2095A-C - LTC6655BHLS8-5V Demo Board | Ultra Low Noise, 5V Precision Voltage Reference in Ceramic Package

Mar 27th 2015
Demonstration circuit 2095A features the LTC®6655, a precision low drift reference packaged in a hermetic LS8. The demonstration circuit is available with the 2.5V, 4.096V or 5V output voltage option parts. ...

Demo Board 

 

DC2095A-B - LTC6655BHLS8-4V Demo Board | Ultra Low Noise, 4.096V Precision Voltage Reference in Ceramic Package

Mar 27th 2015
Demonstration circuit 2095A features the LTC®6655, a precision low drift reference packaged in a hermetic LS8. The demonstration circuit is available with the 2.5V, 4.096V or 5V output voltage option parts. ...

Demo Board 

 

DC2095A-A - LTC6655BHLS8-2.5V Demo Board | Ultra Low Noise, 2.5V Precision Voltage Reference in Ceramic Package

Mar 27th 2015
Demonstration circuit 2095A features the LTC®6655, a precision low drift reference packaged in a hermetic LS8. The demonstration circuit is available with the 2.5V, 4.096V or 5V output voltage option parts. ...

Demo Board 

 

DC2126A - High-Accuracy Wireless Temperature Sensor with Solar Battery Life Extender

Aug 12th 2014
The DC2126A is a high-accuracy wireless temperature sensor, powered from ambient light, built using Linear Technology integrated circuits. A 24-bit delta-sigma ADC reads a thermistor biased from a precision voltage reference. A switching power supply harvests energy from the built-in solar panel, and automatically switches over ...

Demo Board 

 

Product How-to: Precise Wireless Temperature Sensor Powers Itself

Jun 13th 2014
In case you missed it, LTC’s Kris Lokere recently wrote an article for EDN describing a circuit combining Dust, Energy Harvesting, and precision temperature sensing. Specifically, it describes a reference circuit showcasing: Dust Networks wireless - LTP5901-IPM SmartMesh IP Mote Energy Harvesting - LTC3330 Nanopower ...

Blog Post 

 

Digital Gain Compression (DGC) for SAR ADCs

Mar 11th 2014
The LTC2378-20 offers a digital gain compression (DGC) feature which defines the full-scale input swing to be between 10% and 90% of the ±VREF analog input range. This feature allows the SAR ADC driver to be powered off of a single positive supply since each input swings between 0.5V and 4.5V as shown in the figure below. Needing ...

Blog Post 

 

Can You Use the Voltage Reference to Power Your ADC Driver?

Kris Lokere - Strategic Applications Manager Jul 11th 2013
Linear Technology’s family of 16-, 18-, and 20-Bit SAR ADCs (LTC2378-20 family) operates with an external reference voltage of up to 5V. The largest input voltage that you are then supposed to put on each ADC input pin is equal to that 5V reference voltage. It seems logical to use an opamp on a 5V supply with rail-to-rail ...

Blog Post 

 

DC1925A-C - LTC2376-20 Demo Board | 20-Bit, 250ksps, SAR ADC with 104dB SNR. Req DC2026

May 1st 2013
The LTC®2378-20, LTC2377-20 and LTC2376-20 are 20‑bit, low power, low noise SAR ADCs with serial outputs that operate from a single 2.5V supply. The following text refers to the LTC2378-20 but applies to all parts in the family, the only difference being the maximum sample rate. The LTC2378-20 supports a ±5V fully ...

Demo Board Linduino LinearLabTools PScope QuikEval System 

 

DC1925A-B - LTC2377-20 Demo Board | 20-Bit, 500ksps, SAR ADC with 104dB SNR. Req DC2026

May 1st 2013
The LTC®2378-20, LTC2377-20 and LTC2376-20 are 20‑bit, low power, low noise SAR ADCs with serial outputs that operate from a single 2.5V supply. The following text refers to the LTC2378-20 but applies to all parts in the family, the only difference being the maximum sample rate. The LTC2378-20 supports a ±5V fully ...

Demo Board Linduino LinearLabTools PScope QuikEval System 

 

DC1925A-A - LTC2378-20 Demo Board | 20-Bit, 1Msps, SAR ADC with 104dB SNR. Req DC2026

Apr 10th 2013
The LTC®2378-20, LTC2377-20 and LTC2376-20 are 20‑bit, low power, low noise SAR ADCs with serial outputs that operate from a single 2.5V supply. The following text refers to the LTC2378-20 but applies to all parts in the family, the only difference being the maximum sample rate. The LTC2378-20 supports a ±5V fully ...

Demo Board Linduino LinearLabTools PScope QuikEval System 

 

LS8 Package Improves Stability of Voltage References

Brendan Whelan - Design Manager Feb 12th 2013
Stability of precision electronic circuits is often dominated by the stability of the voltage reference. Most electronic systems rely on one or more voltage references to ensure that measurements or performance meets specifications, especially over long periods of time. Environmental factors directly affect the stability of ...

Video 

 

DC1826A-E - LTC2389-16 with LTC6655/LT6201, 16-Bit, 2.5Msps, Serial/Parallel SAR ADC with 96dB SNR. Req DC718

Jul 9th 2012
DC1826A-E - Demo Board for:LTC2389-16 - 16-Bit, 2.5Msps SAR ADC with Pin-Configurable Analog Input Range and 96dB SNRLTC6655 - 0.25ppm Noise, Low Drift Precision ReferencesLT6201 - Dual 165MHz, Rail-to-Rail Input and Output, 0.95nV/√Hz Low Noise, Op Amp Family ...

Demo Board LinearLabTools PScope 

 

DC1805A-H - LTC6362 with 250ksps 18-bit LTC2376-18 SAR ADC, LTC6655-5. Req DC718 or DC2026

Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1805A-G - LTC6362 with 500ksps 18-bit LTC2377-18 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1805A-F - LTC6362 with 1Msps 18-bit LTC2378-18 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1805A-E - LTC6362 with 1.6Msps 18-bit LTC2379-18 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1805A-D - LTC6362 with 250ksps 16-bit LTC2376-16 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1805A-C - LTC6362 with 500ksps 16-bit LTC2377-16 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1805A-B - LTC6362 with 1Msps 16-bit LTC2378-16 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

May 17th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1805A-A - LTC6362 with 2Msps 16-bit LTC2380-16 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

May 16th 2012
DC1805A-A - Demo Board for:LTC2380-16 - 16-Bit, 2Msps, Low Power SAR ADC with 96dB SNRLTC6362 - Precision, Low Power Rail-to-Rail Input/Output Differential Op Amp/SAR ADC DriverLTC6655 - 0.25ppm Noise, Low Drift Precision References ...

Demo Board Linduino PScope QuikEval System 

 

DC1813A-D - LTC2364-16 with LTC6655-5/LT6202 Demo Board | 16-Bit, 250ksps, Pseudo-Differential Unipolar SAR ADC with 94.7dB SNR. Req DC718 or DC590

May 2nd 2012
DC1813A-D - Demo Board for:LTC2364-16 - 16-Bit, 250ksps, Pseudo-Differential Unipolar SAR ADC with 94.7dB SNR ...

Demo Board Linduino PScope QuikEval System 

 

DC1813A-C - LTC2367-16 with LTC6655-5/LT6202 Demo Board |16-Bit, 500ksps, Pseudo-Differential Unipolar SAR ADC with 94.7dB SNR. Req DC718 or DC590

May 2nd 2012
DC1813A-C - Demo Board for:LTC2367-16 - 16-Bit, 500ksps, Pseudo- Differential Unipolar SAR ADC with 94.7dB SNRLT6202 - Single 100MHz, Rail-to-Rail Input and Output, Ultralow 1.9nVrtHz Noise, Low Power Op AmpsLTC6655 - 0.25ppm Noise, Low Drift Precision References ...

Demo Board Linduino PScope QuikEval System 

 

DC1813A-B - LTC2368-16 with LTC6655-5/LT6202 Demo Board | 16-Bit, 1Msps, Pseudo-Differential Unipolar SAR ADC with 94.7dB SNR. Req DC718 or DC590

May 2nd 2012
DC1813A-B - Demo Board for:LTC2368-16 - 16-Bit, 1Msps, Pseudo- Differential Unipolar SAR ADC with 94.7dB SNRLT6202 - Single 100MHz, Rail-to-Rail Input and Output, Ultralow 1.9nVrtHz Noise, Low Power Op AmpsLTC6655 - 0.25ppm Noise, Low Drift Precision References ...

Demo Board Linduino PScope QuikEval System 

 

DC1813A-H - LTC2364-18 with LTC6655-5/LT6202 Demo Board | 18-Bit, 250ksps, Pseudo-Differential Unipolar SAR ADC with 97dB SNR. Req DC718 or DC590

May 2nd 2012
DC1813A-H - Demo Board for:LTC2364-18 - 18-Bit, 250ksps, Pseudo-Differential Unipolar SAR ADC with 97dB SNRLT6202 - Single 100MHz, Rail-to-Rail Input and Output, Ultralow 1.9nVrtHz Noise, Low Power Op AmpsLTC6655 - 0.25ppm Noise, Low Drift Precision References ...

Demo Board Linduino PScope QuikEval System 

 

DC1813A-G - LTC2367-18 with LTC6655-5/LT6202 Demo Board | 18-Bit, 500ksps, Pseudo-Differential Unipolar SAR ADC with 97dB SNR. Req DC718 or DC590

May 2nd 2012
DC1813A-G - Demo Board for:LTC2367-18 - 18-Bit, 500ksps, Pseudo-Differential Unipolar SAR ADC with 97dB SNRLTC6655 - 0.25ppm Noise, Low Drift Precision ReferencesLT6202 - Single 100MHz, Rail-to-Rail Input and Output, Ultralow 1.9nVrtHz Noise, Low Power Op Amps ...

Demo Board Linduino PScope QuikEval System 

 

DC1813A-F - LTC2368-18 with LTC6655-5/LT6202 Demo Board |18-Bit, 1Msps, Pseudo-Differential Unipolar SAR ADC with 97dB SNR. Req DC718 or DC590

May 2nd 2012
DC1813A-F - Demo Board for:LTC2368-18 - 18-Bit, 1Msps, Pseudo-Differential Unipolar SAR ADC with 97dB SNRLTC6655 - 0.25ppm Noise, Low Drift Precision ReferencesLT6202 - Single 100MHz, Rail-to-Rail Input and Output, Ultralow 1.9nVrtHz Noise, Low Power Op Amps ...

Demo Board Linduino PScope QuikEval System 

 

DC1826A-A - LTC2389-18 with LTC6655/LT6201, 18-Bit, 2.5Msps, Serial/Parallel SAR ADC with 99.8dB SNR. Req DC718

Apr 24th 2012
DC1826A-A - Demo Board for:LTC2389-18 - 18-Bit, 2.5Msps SAR ADC with Pin-Configurable Analog Input Range and 99.8dB SNRLTC6655 - 0.25ppm Noise, Low Drift Precision ReferencesLT6201 - Dual 165MHz, Rail-to-Rail Input and Output, 0.95nV/√Hz Low Noise, Op Amp Family ...

Demo Board LinearLabTools PScope 

 

DC1783A-H - LTC2376-18 with LTC6655-5/LT6350 Demo Board | 18-Bit, 250ksps, SAR ADC with 102dB SNR. Req DC718 or DC2026

Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

DC1783A-G - LTC2377-18 with LTC6655-5/LT6350 Demo Board | 18-Bit, 500ksps, SAR ADC with 102dB SNR. Req DC718 or DC2026

Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

DC1783A-F - LTC2378-18 with LTC6655-5/LT6350 Demo Board | 18-Bit, 1Msps, SAR ADC with 102dB SNR. Req DC718 or DC2026

Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

DC1783A-D - LTC2376-16 with LTC6655-5/LT6350 Demo Board | 16-Bit, 250ksps, SAR ADC with 97dB SNR. Req DC718 or DC2026

Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

DC1783A-C - LTC2377-16 with LTC6655-5/LT6350 Demo Board | 16-Bit, 500ksps, SAR ADC with 97dB SNR. Req DC718 or DC2026

Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

DC1783A-B - LTC2378-16 with LTC6655-5/LT6350 Demo Board | 16-Bit, 1Msps, SAR ADC with 97dB SNR. Req DC718 or DC2026

Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

DC1813A-E - LTC2369-18 with LTC6655-5/LT6202 Demo Board | 18-Bit, 1.6Msps, Pseudo-Differential Unipolar SAR ADC with 96.5dB SNR. Req DC718 or DC590

Nov 7th 2011
DC1813A-E - Demo Board for:LTC2369-18 - 18-Bit, 1.6Msps, Pseudo- Differential Unipolar SAR ADC with 96.5dB SNRLTC6655 - 0.25ppm Noise, Low Drift Precision ReferencesLT6202 - Single 100MHz, Rail-to-Rail Input and Output, Ultralow 1.9nVrtHz Noise, Low Power Op Amps ...

Demo Board Linduino PScope QuikEval System 

 

DC1813A-A - LTC2370-16 with LTC6655-5/LT6202 Demo Board | 16-Bit, 2Msps, Pseudo-Differential Unipolar SAR ADC with 94dB SNR. Req DC718 or DC590

Nov 7th 2011
DC1813A-A - Demo Board for:LTC2370-16 - 16-Bit, 2Msps, Pseudo- Differential Unipolar SAR ADC with 94dB SNRLTC6655 - 0.25ppm Noise, Low Drift Precision ReferencesLT6202 - Single 100MHz, Rail-to-Rail Input and Output, Ultralow 1.9nVrtHz Noise, Low Power Op Amps ...

Demo Board Linduino PScope QuikEval System 

 

DC1783A-A - LTC2380-16 with LTC6655-5/LT6350 Demo Board | 16-Bit, 2Msps, SAR ADC with 96dB SNR. Req DC718 or DC2026A

Mar 23rd 2011
DC1783A-A - Demo Board for:LTC2380-16 - 16-Bit, 2Msps, Low Power SAR ADC with 96dB SNRLTC6655 - 0.25ppm Noise, Low Drift Precision ReferencesLT6350 - Low Noise Single-Ended to Differential Converter/ADC Driver ...

Demo Board Linduino PScope QuikEval System 

 

DC1783A-E - LTC2379-18 with LTC6655-5/LT6350 Demo Board | 18-Bit, 1.6Msps, SAR ADC with 101dB SNR. Req DC718 or DC2026

Mar 4th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

Innovation Pushes State-of-the-Art in Voltage References

Brendan Whelan - Design Manager Nov 8th 2010
Most system designers use voltage references in their circuits. While many will agree that the performance may ultimately be limited by the reference, they are often unclear as to why. With so many reference products available, designers often choose based on a tradeoff between price and precision, using only initial accuracy ...

Video 

 

SOT23 Voltage Reference Offers 10ppm/°C Drift While Limiting Noise to Only 1.6ppm

Aug 11th 2010
MILPITAS, CA - August 11, 2010 - Linear Technology introduces the LT6654, a SOT23 series voltage reference designed specifically for precision operation from -40°C to 125°C. This voltage reference combines 0.05% initial accuracy, 10ppm temperature drift and low frequency noise of only 1.6ppm. The LT6654 can operate on a supply ...

Press Release 

 

10ppm/ºC, 3mV Dropout Voltage Reference Operates with Less than 1μA

Apr 5th 2010
MILPITAS, CA — April 5, 2010 — Linear Technology announces the LT6656, a precision SOT23 voltage reference that operates on only 850nA of supply current. The LT6656 has an initial error of less than 0.05% and a guaranteed temperature drift of less than 10ppm/ºC. This combination of precision and ultralow power is ideal ...

Press Release 

 

LTC6655 0.25ppm Noise, Low Drift Precision Buffered Reference Family - Video Product Brief

Lailanie Reyes - Marketing Admin Jan 5th 2010
The LTC6655 is a complete family of precision bandgap voltage references, offering exceptional noise and drift performance. This low noise and drift is ideally suited for the high resolution measurements required by instrumentation and test equipment. In addition, the LTC6655 is fully specified over the temperature range of ...

Video 

 

Industry's Lowest Noise 2.5V Voltage Reference Features 2ppm/ºC Max Drift

Sep 21st 2009
MILPITAS, CA - September 21, 2009 - Linear Technology announces the LTC6655, an ultra-stable voltage reference with an unequaled noise level of only 625nVp-p (0.25ppmp-p) from 0.1Hz to 10Hz. Click Photo for High-Res Image   The LTC6655 is an ideal companion to high resolution DACs and ADCs required by instrumentation ...

Press Release 

 

775 Nanovolt Noise Measurement for a Low Noise Voltage Reference

Jim Williams - Applications Guru Sep 15th 2009
Frequently, voltage reference stability and noise define measurement limits in instrumentation systems. In particular, reference noise often sets stable resolution limits. Reference voltages have decreased with the continuing drop in system power supply voltages, making reference noise increasingly important. The compressed ...

Video 

 

Build Your Own Laboratory Precision Voltage Source - LT1236, LT1881, LT1010, LT1017

Mark Thoren - Staff Scientist Jun 15th 2008
Every electronics lab needs a couple different types of voltage sources. Power supplies are the obvious choice, but these bench top supplies are not very stable over time and temperature, they cannot sink current and it can be very difficult to set an accurate voltage. This video gives a step-by-step demonstration of an amplifier ...

Video 

 

5ppm/°C Voltage Reference Features Very Low Noise

Dec 13th 2007
MILPITAS, CA - December 13, 2007 - Linear Technology Corporation announces the LTC6652, a precision low noise series voltage reference with an initial accuracy of 0.05% and maximum voltage drift of 5ppm/°C. The LTC6652 offers excellent load and line regulation, and noise of only 2.1ppm. The combination of precision and low ...

Press Release 

 

Precision Voltage Reference in a Tiny 2mm x 2mm DFN Package

Jan 25th 2006
MILPITAS, CA - January 25, 2006 - Linear Technology Corporation announces the LT6660, the industry's first precision series voltage reference to use the tiny 3-lead 2mm x 2mm DFN package. These compact devices combine 0.2% initial accuracy and 20ppm drift with micro-power operation and require less than half the space of the SOT-23 ...

Press Release