1. Skip to navigation
  2. Skip to content
  3. Skip to sidebar

Solutions Search - Monitor, Control and Protection

Terasic Innovate FPGA Design Contest

Nov 2nd 2017
Welcome to the Innovate FPGA & SoC Design Contest held by Terasic, Analog Devices & Intel. For the past 14 years, this contest has inspired thousands of aspiring engineers to design, to create, and innovate!    YOU MAY PICK 3 FREE LTC / ADI PLUG-IN BOARDS (EITHER FROM THE ARDUINO OR QUIKEVAL CATEGORIES) BY ...

Circuit 

 

LT8672 12V, 5A Automotive Reverse Battery Protection

Oct 6th 2017
The LT®8672 is an active rectifier controller for reverse input protection. It drives an external N-channel MOSFET to replace a power Schottky diode. Its very low quiescent current and fast transient response meet the tough requirements in automotive applications where AC input signals of up to 100kHz are present. These ...

Circuit LTspice 

 

LT4320 LT4320 Ideal Diode Bridge

Jan 27th 2017
The LT®4320/LT4320-1 are ideal diode bridge controllers that drive four N-channel MOSFETs, supporting voltage rectification from DC to 600Hz typical. By maximizing available voltage and reducing power dissipation (see thermograph comparison below), the ideal diode bridge simplifies power supply design and reduces power supply ...

Circuit 

 

LTC3723-1 130W Isolated Push-Pull Converter for PoE Applications with 93.5% Peak Efficiency

Jeoffrey (Zijian) Wang - Applications Engineer Oct 3rd 2016
This solution is a non-synchronous isolated push-pull converter designed for PoE applications, which can generate a 50V/2.6A output from a 34-38V (36V typical) input voltage range. A 93.5% peak efficiency is achieved for the whole isolated converter and the total solution can be fit into 1/8 brick footprint (2.3” x 0.9”) ...

Circuit LTspice 

 

LTC3126 5V, 2MHz Step-Down Converter with Dual Inputs

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LTC3126 12V, 2MHz Step-Down Converter with Dual Inputs

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LTC3126 1.8V, 2MHz Step-Down Converter with Dual Inputs

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LTC3126 3.3V, 2MHz Step-Down Converter with Dual Inputs

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LTC3126 3.3V Supply with 200ms Transient Ride-Through Capability

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LT3090 5V to +/-2.5V Low Noise Power Supply

Sep 15th 2016
The LT®3090 is a 600mA, low dropout negative linear regulator that is easily parallelable to increase output current or spread heat on surface mounted boards. Designed with a precision current reference followed by a high performance rail-to-rail voltage buffer, this regulator finds use in applications requiring precision ...

Circuit 

 

LT3090 Two-Terminal Current Source

Sep 15th 2016
The LT®3090 is a 600mA, low dropout negative linear regulator that is easily parallelable to increase output current or spread heat on surface mounted boards. Designed with a precision current reference followed by a high performance rail-to-rail voltage buffer, this regulator finds use in applications requiring precision ...

Circuit 

 

LT3090 500mA LED Driver with Grounded LED Tab (Heatsink)

Sep 15th 2016
The LT®3090 is a 600mA, low dropout negative linear regulator that is easily parallelable to increase output current or spread heat on surface mounted boards. Designed with a precision current reference followed by a high performance rail-to-rail voltage buffer, this regulator finds use in applications requiring precision ...

Circuit 

 

LT8391 93% Efficient 84W Buck-Boost LED Driver from 24VAC

Sep 2nd 2016
The LT®8391 is a synchronous 4-switch buck-boost LED controller that regulates LED current from input voltage above, below, or equal to the output voltage. The proprietary peak-buck peak-boost current mode control scheme allows adjustable and synchronizable 150kHz to 650kHz fixed frequency operation, or internal ±15% ...

Circuit 

 

LTC3130 Multiple VIN 5V Out Application, Using the LTC4412 PowerPath Controller

Aug 15th 2016
The LTC3130/LTC3130-1 are high efficiency, low noise, 600mA buck-boost converters with wide VIN and VOUT ranges. For high efficiency operation at light loads, BurstMode operation can be selected, reducing the quiescent current to just 1.6µA. Converter start-up is achieved from sources as low as 7.5µW. ...

Circuit 

 

MAX 10 NEEK Development Kit

Oct 5th 2015
The MAX 10 NEEK from Terasic is a full featured embedded evaluation kit based upon the MAX10 family of Altera FPGAs. It offers a comprehensive design environment with everything embedded developers need to create a processing based system. The MAX 10 NEEK delivers an integrated platform that includes hardware, design tools, ...

Circuit 

 

LT3091 Parallel Linear Regulators For -10V to -3Vin, -2.5Vout@3A

Aug 28th 2015
The LT®3091 is a 1.5A, low dropout negative linear regulator that is easily paralleled to increase output current or spread heat on surface mounted boards. Designed with a precision current reference followed by a high performance rail-to-rail voltage buffer, this regulator finds use in applications requiring precision output, ...

Circuit 

 

LT3091 -10V to -3Vin, -2.5Vout@1.5A Negative Output Linear Regulator

Aug 28th 2015
The LT®3091 is a 1.5A, low dropout negative linear regulator that is easily paralleled to increase output current or spread heat on surface mounted boards. Designed with a precision current reference followed by a high performance rail-to-rail voltage buffer, this regulator finds use in applications requiring precision output, ...

Circuit 

 

LT3091 Floating 3-Terminal Regulator (for Arbitrarily High Voltage Applications)

Aug 28th 2015
The LT®3091 is a 1.5A, low dropout negative linear regulator that is easily paralleled to increase output current or spread heat on surface mounted boards. Designed with a precision current reference followed by a high performance rail-to-rail voltage buffer, this regulator finds use in applications requiring precision output, ...

Circuit 

 

Achieving Low On-Resistance with Guaranteed SOA in High Current Hot Swap Applications

Dan Eddleman - Senior Applications Engineer
Gabino Alonso - Strategic Marketing Engineer
Jul 29th 2015
Introduction The requirement for live insertion and removal in high current backplane applications demands MOSFETs that exhibit both low on-resistance during steady state operation and high Safe Operating Area (SOA) for transient conditions. Often, modern MOSFETs optimized for low on-resistance are unsuitable for high SOA Hot ...

Blog Post Circuit LTspice 

 

Altera Arria 10 FPGA Development Kit

Jul 17th 2015
The LTC3877 + LTC3874 are used to provide power for the Core Rail by taking advantage of the 6-bit parallel VID that interfaces with the 20-nm Arria 10’s SmartVID to reduce the FPGA’s static and dynamic power consumption, and Ultralow value and temperature compensated DCR load current sensing which maximizes ...

Circuit 

 

LTC2956 Wake-Up Timer with Pushbutton Control

Mar 19th 2015
The LTC®2956 is a micropower, wide input voltage range, configurable wake-up timer with pushbutton control. It periodically wakes up and turns on a connected system to perform tasks like monitoring temperature or capturing images. After completing the task, the LTC2956 turns the system off to conserve power. ...

Circuit 

 

LTC2956 Micropower Time-Lapse Photography Intervalometer

Mar 19th 2015
The LTC®2956 is a micropower, wide input voltage range, configurable wake-up timer with pushbutton control. It periodically wakes up and turns on a connected system to perform tasks like monitoring temperature or capturing images. After completing the task, the LTC2956 turns the system off to conserve power. ...

Circuit 

 

LTC2956 Micropower, Reverse Battery Protected Pushbutton Controller and Sleep Timer with Hot-Swap Controller

Mar 19th 2015
The LTC®2956 is a micropower, wide input voltage range, configurable wake-up timer with pushbutton control. It periodically wakes up and turns on a connected system to perform tasks like monitoring temperature or capturing images. After completing the task, the LTC2956 turns the system off to conserve power. ...

Circuit 

 

LTC2956 Low IQ Timer with 10% Duty Cycle

Mar 19th 2015
The LTC®2956 is a micropower, wide input voltage range, configurable wake-up timer with pushbutton control. It periodically wakes up and turns on a connected system to perform tasks like monitoring temperature or capturing images. After completing the task, the LTC2956 turns the system off to conserve power. ...

Circuit 

 

LTC3118 System Power (Priority) or 3-Cell Li-Ion to 5V VOUT Regulator with Automatic Burst Mode Operation

Mar 19th 2015
The LTC®3118 is a dual-input, wide voltage range synchronous buck-boost DC/DC converter with an intelligent, integrated, low-loss PowerPath control. The unique power switch architecture provides efficient operation from either input source to a programmable output voltage above, below or equal to the input. Voltage capability ...

Circuit 

 

LTC3118 Dual Battery System to 3.3V VOUT, Runs from Lead Acid (Priority) When Present Automatic Burst Mode Operation

Mar 19th 2015
The LTC®3118 is a dual-input, wide voltage range synchronous buck-boost DC/DC converter with an intelligent, integrated, low-loss PowerPath control. The unique power switch architecture provides efficient operation from either input source to a programmable output voltage above, below or equal to the input. Voltage capability ...

Circuit 

 

LTC4218 12V / 100A Hot Swap Design for Server Farms

Dan Eddleman - Senior Applications Engineer Mar 18th 2015
Cultivate reliability on the farm with a properly designed Hot Swap circuit. Introduction As data centers servicing the cloud grow in speed and capacity, backplane supplies are called on to deliver currents that push the performance boundaries of Hot Swap™ components. Hot Swap solutions allow boards to be inserted and ...

Blog Post Circuit LTspice 

 

LTC4226 Parallel MOSFETs in Hot Swap Circuits

Dan Eddleman - Senior Applications Engineer
Gabino Alonso - Strategic Marketing Engineer
Mar 13th 2015
The Good, the Bad, and the Ugly Introduction While it is often desirable, and sometimes absolutely critical, to use multiple parallel MOSFETs in Hot Swap™ circuits, careful analysis of Safe Operating Area (SOA) is essential. Each additional parallel MOSFET added to a circuit improves the voltage drop, power loss, and ...

Blog Post Circuit LTspice 

 

LTC3118 12V VIN to 5V VOUT Converter with Capacitor Backup Runs from VIN1 (Priority) in Normal Mode, VIN2 During Backup Event

Feb 24th 2015
The LTC®3118 is a dual-input, wide voltage range synchronous buck-boost DC/DC converter with an intelligent, integrated, low-loss PowerPath control. The unique power switch architecture provides efficient operation from either input source to a programmable output voltage above, below or equal to the input. Voltage capability ...

Circuit 

 

LTC7860 3.5V to 60V Input, 12V/18V Maximum 5A Output at 535kHz

Feb 24th 2015
The LTC®7860 high efficiency surge stopper protects loads from high voltage transients. High efficiency permits higher currents and smaller solution sizes. During an input overvoltage event, such as a load dump in vehicles, the LTC7860 controls the gate of an external MOSFET to act as a switching DC/DC regulator (PROTECTIVE ...

Circuit 

 

LTM4639 1.8V at 20A uModule Design with Input Current and Temperature Monitoring

Nov 24th 2014
The LTM®4639 is a complete 20A output high efficiency switch mode step-down DC/DC μModule (micromodule) regulator. Included in the package are the switching controller, power FETs, inductor and compensation components. Operating over an input voltage range from 2.375V to 7V, the LTM4639 supports an output voltage range ...

Circuit 

 

LTC2946 Power, Charge and Energy Monitoring in –48V System Using Low Side Sensing (1.5kHz I2C Interface)

Sep 18th 2014
The LTC®2946 is a rail-to-rail system monitor that measures current, voltage, power, charge and energy. It features an operating range of 2.7V to 100V and includes a shunt regulator for supplies above 100V. The current measurement common mode range of 0V to 100V is independent of the input supply. A 12-bit ADC measures load ...

Circuit 

 

LTC2946 Bidirectional Power Monitor with Energy and Charge Monitor in Forward Path

Sep 18th 2014
The LTC®2946 is a rail-to-rail system monitor that measures current, voltage, power, charge and energy. It features an operating range of 2.7V to 100V and includes a shunt regulator for supplies above 100V. The current measurement common mode range of 0V to 100V is independent of the input supply. A 12-bit ADC measures load ...

Circuit 

 

LTC2946 Dual Power, Charge and Energy Monitor Using Single Opto-Coupler for Galvanic Isolation and Blocking Diodes for Data Retention When Either Supply Fails

Sep 18th 2014
The LTC®2946 is a rail-to-rail system monitor that measures current, voltage, power, charge and energy. It features an operating range of 2.7V to 100V and includes a shunt regulator for supplies above 100V. The current measurement common mode range of 0V to 100V is independent of the input supply. A 12-bit ADC measures load ...

Circuit 

 

LTC2946 Power, Charge and Energy Monitor for Main Supply and Power Monitor for Secondary Supply with Single LTC2946

Sep 18th 2014
The LTC®2946 is a rail-to-rail system monitor that measures current, voltage, power, charge and energy. It features an operating range of 2.7V to 100V and includes a shunt regulator for supplies above 100V. The current measurement common mode range of 0V to 100V is independent of the input supply. A 12-bit ADC measures load ...

Circuit 

 

LTC2946 Power, Charge and Energy Monitor in –48V Harsh Environment Using INTVCC Shunt Regulator to Tolerate 200V Transients

Sep 18th 2014
The LTC®2946 is a rail-to-rail system monitor that measures current, voltage, power, charge and energy. It features an operating range of 2.7V to 100V and includes a shunt regulator for supplies above 100V. The current measurement common mode range of 0V to 100V is independent of the input supply. A 12-bit ADC measures load ...

Circuit 

 

LTC2946 6V to 300V High Side Power, Charge and Energy Monitor

Sep 18th 2014
The LTC®2946 is a rail-to-rail system monitor that measures current, voltage, power, charge and energy. It features an operating range of 2.7V to 100V and includes a shunt regulator for supplies above 100V. The current measurement common mode range of 0V to 100V is independent of the input supply. A 12-bit ADC measures load ...

Circuit 

 

LTC3788 Generates High Voltages Using a Two-Stage Boost Converter

Victor Khasiev - Applications Engineer
Gabino Alonso - Strategic Marketing Engineer
Sep 17th 2014
Generating high voltages from low level sources is not an easy task. Engineers are facing the following problems when they try to implement single stage boost at high step-up ratios. Limitation of maximum duty cycle in boost controllers Sharp decrease in efficiency at long duty cycles High peak currents and EMI challenges ...

Blog Post Circuit LTspice 

 

LTC3803/LTC4441 6V -24V Input Voltage to 52V/2A Boost Converter

Sep 4th 2014
The LTC®4441/LTC4441-1 is an N-channel MOSFET gate driver that can supply up to 6A of peak output current. The chip is designed to operate with a supply voltage of up to 25V and has an adjustable linear regulator for the gate drive. The gate drive voltage can be programmed between 5V and 8V. ...

Circuit LTspice 

 

LTC4252B-1 –48V/2.5A Hot Swap Controller

Sep 2nd 2014
The LTC®4252 negative voltage Hot SwapTM controller allows a board to be safely inserted and removed from a live backplane. Output current is controlled by three stages of current limiting: a timed circuit breaker, active current limiting and a fast feedforward path that limits peak current under worst-case catastrophic ...

Circuit LTspice 

 

LTC3225 5V Supercapacitor Back-Up Supply

Aug 7th 2014
The LTC3225/LTC3225-1 are programmable supercapacitor chargers designed to charge two supercapacitors in series to a selectable fixed output voltage (4.8V/5.3V for the LTC3225 and 4V/4.5V for the LTC3225-1) from input supplies as low as 2.8V to 5.5V. Automatic cell balancing prevents overvoltage damage to either supercapacitor. ...

Circuit LTspice 

 

LTC4366 Surge Protected Automotive 12V Supply

Aug 4th 2014
The LTC®4366 surge stopper protects loads from high voltage transients. By controlling the gate of an external N-channel MOSFET, the LTC4366 regulates the output during an overvoltage transient. The load may remain operational while the overvoltage is dropped across the MOSFET. Placing a resistor in the return line isolates ...

Circuit LTspice 

 

LTC4211 Single Channel 5V Hot Swap Controller

Aug 4th 2014
The LTC4211 is a Hot Swap controller that allows a board to be safely inserted and removed from a live backplane. An internal highside switch driver controls the gate of an external N-channel MOSFET for supply voltages ranging from 2.5V to 16.5V. The LTC4211 provides soft-start and in rush current limiting during the start-up ...

Circuit LTspice 

 

LTC4217 Single Channel 12V, 1.5A Hot Swap Controller

Aug 4th 2014
The LTC4217 is an integrated solution for Hot Swap™ applications that allows a board to be safely inserted and removed from a live backplane. The part integrates a Hot Swap controller, power MOSFET and current sense resistor in a single package for small form factor applications. A dedicated 12V version (LTC4217-12) contains ...

Circuit LTspice 

 

LTC4364-1 4A, 12V Overvoltage Output Regulator with Ideal Diode Withstands 200V 1ms Transient at VIN

Aug 4th 2014
The LTC4364 surge stopper with ideal diode controller protects loads from high voltage transients. It limits and regulates the output during an overvoltage event, such as load dump in automobiles, by controlling the voltage drop across an external N-channel MOSFET pass device. The LTC4364 also includes a timed, current limited ...

Circuit LTspice 

 

LTC4261 –48V/200W Hot Swap Controller with I2C and ADC

Aug 4th 2014
The LTC®4261/LTC4261-2 negative voltage Hot SwapTM controllers allow a board to be safely inserted and removed from a live backplane. Using an external N-channel pass transistor, the board supply voltage can be ramped at an adjustable rate. The devices feature independently adjustable inrush current and overcurrent limits ...

Circuit LTspice 

 

Terasic TR5-Lite Stratix V FPGA Development Kit

Jun 19th 2014
The TR5-Lite Stratix V FPGA Development Kit a slim form-factor PCIe board that features maximum power in a minimum size. Perfect for 1U chassis servers and other stringent environments, the TR5-Lite includes high speed SFP+ interfaces and high-bandwidth memory architecture for high performance computing, cloud systems, and ultra ...

Circuit LTpowerPlanner 

 

Terasic TR5-F40W Stratix V GX FPGA Development Kit

Jun 19th 2014
The Terasic TR5-F40W Stratix V GX FPGA Development Kit provides the ideal hardware platform for developing high-performance and high-bandwidth application. With a standard-height, half-length form-factor package, the TR5-F40W is designed for the most demanding high-end applications, empowered with the top-of-the-line Altera ...

Circuit 

 

Altera Audio Video Development Kit, Stratix IV GX Edition

Jun 12th 2014
The Audio Video Development Kit, Stratix IV GX Edition, delivers a complete video and image processing development environment for design engineers. The kit facilitates the entire design process, from design conception through hardware implementation. This kit includes the Stratix IV EP4SGX230 FPGA development ...

Circuit 

 

Altera Cyclone IV GX Transceiver Starter Kit

Jun 12th 2014
The Altera Cyclone IV FPGA family extends the Cyclone FPGA series leadership in providing the market’s lowest cost, lowest power FPGAs, including a transceiver variant. Ideal for high-volume, cost-sensitive applications, Cyclone IV FPGAs enable you to meet increasing bandwidth requirements while lowering ...

Circuit 

 

Altera Cyclone V GX Development Kit (Discontinued)

Jun 12th 2014
The Altera Cyclone V GX FPGA Development Kit provides a comprehensive, best in-class design environment to quickly begin developing low-cost and low-power FPGA system level designs. This kit helps to shorten your product’s development cycle so that you can meet your product’s time to market and production milestones. Linear ...

Circuit 

 

Terasic DE5-Net Stratix V Board

Jun 12th 2014
The DE5-Net Stratix V FPGA Development Kit is perfectly suited for extreme high powered needs including cloud computing, high frequency trading, and security networks. Featuring an ultra-high bandwidth memory architecture, low-latency SFP+ interfaces, expandable memory, and PCIe communication, the DE5-Net allows ...

Circuit 

 

Altera Stratix IV GX FPGA Development Kit

Jun 12th 2014
The Altera Stratix IV GX FPGA Development Kit delivers a complete system-level design environment that includes both the hardware and software needed to immediately begin developing FPGA designs. With this PCI-SIG-compliant board and a one-year license for Quartus II design software, you can develop and test PCI Express ...

Circuit 

 

Altera 100G Development Kit, Stratix V Edition

Jun 12th 2014
The Altera 100G Development Kit, Stratix V GX Edition enables a thoroughevaluation of 100G designs. It supports 10G/40G and 100G line interfaces through optical modules and the ability to verify a variety of high-speed protocols. Rail / Function  Part Number General Description of Part 0.9V: ...

Circuit 

 

Altera Stratix V GX FPGA Development Kit

Jun 11th 2014
The Altera® Stratix® V GX FPGA Development Kit provides a complete design environment that includes all the hardware and software you need to begin developing FPGA designs immediately. The development kit is RoHS compliant. You can use this development kit to do the following: Develop and test PCI Express® (PCIe®) designs ...

Circuit 

 

Altera Stratix IV E FPGA Development Kit

Jun 5th 2014
The Altera Stratix IV E FPGA Development Kit delivers a complete system-level design environment that includes both the hardware and software needed to immediately begin developing FPGA designs. You can use this development kit to develop and test memory subsystems consisting of DDR3 DIMMs, QDR II+, and RLDRAM ...

Circuit 

 

LTC2933 Low Cost Multipoint Temperature Control System

Apr 2nd 2014
The LTC®2933 is an EEPROM configurable voltage supervisor which can simultaneously monitor up to six power supply voltage inputs. Each voltage detector offers programmable over/undervoltage thresholds in various ranges and increments. ...

Circuit 

 

LT3086 5V, 2.1A USB Supply with Cable Drop Compensation

Dec 3rd 2013
The LT®3086 is a multi-feature, low dropout, low noise 2.1A linear regulator that operates over a 1.4V to 40V input supply range. Dropout voltage at 2.1A is typically 330mV. One resistor sets output voltage from 0.4V to 32V. Output voltage tolerance is guaranteed to ±2% over line, load and temperature. The LT3086 ...

Circuit 

 

LT3086 Adjustable Voltage Controlled Current Source

Dec 3rd 2013
The LT®3086 is a multi-feature, low dropout, low noise 2.1A linear regulator that operates over a 1.4V to 40V input supply range. Dropout voltage at 2.1A is typically 330mV. One resistor sets output voltage from 0.4V to 32V. Output voltage tolerance is guaranteed to ±2% over line, load and temperature. The LT3086 ...

Circuit LTspice 

 

LT3086 Paralleling Two Regulators for 5V, 4.2A with Cable Drop Compensation (CDC)

Dec 3rd 2013
The LT®3086 is a multi-feature, low dropout, low noise 2.1A linear regulator that operates over a 1.4V to 40V input supply range. Dropout voltage at 2.1A is typically 330mV. One resistor sets output voltage from 0.4V to 32V. Output voltage tolerance is guaranteed to ±2% over line, load and temperature. The LT3086 ...

Circuit 

 

LT3086 Paralleling Two Regulators for 5V, 4.2A

Dec 3rd 2013
The LT®3086 is a multi-feature, low dropout, low noise 2.1A linear regulator that operates over a 1.4V to 40V input supply range. Dropout voltage at 2.1A is typically 330mV. One resistor sets output voltage from 0.4V to 32V. Output voltage tolerance is guaranteed to ±2% over line, load and temperature. The LT3086 ...

Circuit 

 

LT3086 Load Current Monitoring Using Power Good

Dec 3rd 2013
The LT®3086 is a multi-feature, low dropout, low noise 2.1A linear regulator that operates over a 1.4V to 40V input supply range. Dropout voltage at 2.1A is typically 330mV. One resistor sets output voltage from 0.4V to 32V. Output voltage tolerance is guaranteed to ±2% over line, load and temperature. The LT3086 ...

Circuit 

 

LT8697 2MHz 5V Step-Down Converter with Cable Drop Compensation

Jul 9th 2013
The LT®8697 is a compact, high efficiency, high speed synchronous monolithic step-down switching regulator designed to power 5V USB applications. A precise output voltage and programmable cable drop compensation maintain accurate 5V regulation at the USB socket connected to the end of a long cable. Forced continuous operation ...

Circuit LTspice 

 

LT3081 Wide Safe Operating Area Supply Using Paralleling Regulators

May 20th 2013
The LT®3081 is a 1.5A low dropout linear regulator designed for rugged industrial applications. Key features of the IC are the extended safe operating area (SOA), output current monitor, temperature monitor and programmable current limit. The LT3081 can be paralleled for higher output current or heat spreading. The device ...

Circuit LTspice 

 

Using the LT3081 as a Current Source

May 20th 2013
The LT®3081 is a 1.5A low dropout linear regulator designed for rugged industrial applications. Key features of the IC are the extended safe operating area (SOA), output current monitor, temperature monitor and programmable current limit. The LT3081 can be paralleled for higher output current or heat spreading. The device ...

Circuit 

 

LT3081 Using IMON to Compensate for Cable Drops

May 20th 2013
The LT®3081 is a 1.5A low dropout linear regulator designed for rugged industrial applications. Key features of the IC are the extended safe operating area (SOA), output current monitor, temperature monitor and programmable current limit. The LT3081 can be paralleled for higher output current or heat spreading. The device ...

Circuit 

 

LT3081: Wide Safe Operating Area Supply

May 20th 2013
The LT3081 is a 1.5A low dropout linear regulator designed for rugged industrial applications. Key features of the IC are the extended safe operating area (SOA), output current monitor, temperature monitor and programmable current limit. The LT3081 can be paralleled for higher output current or heat spreading. The device withstands ...

Circuit LTspice 

 

Priority Switching from 12V Main Supply to 14.8V Battery Backup

Nov 27th 2012
The LTC4417 connects one of three valid power supplies to a common output based on priority. Priority is defined by pin assignment, with V1 assigned the highest priority and V3 the lowest priority. A power supply is defined as valid when its voltage has been within its overvoltage (OV) and undervoltage (UV) window continuously ...

Circuit LTspice 

 

LTM4641 1V, 40A Fault-Protected Load

Oct 15th 2012
The LTM®4641 is a switch mode step-down DC/DC μModule® (micromodule) regulator with advanced input and load protection features. Trip detection thresholds for the following faults are customizable: input undervoltage, overtemperature, input overvoltage and output overvoltage. Select fault conditions can be set for ...

Circuit 

 

LTM4641 1V, 20A Fault-Protected Load from Up to 38VIN

Oct 15th 2012
The LTM®4641 is a switch mode step-down DC/DC μModule® (micromodule) regulator with advanced input and load protection features. Trip detection thresholds for the following faults are customizable: input undervoltage, overtemperature, input overvoltage and output overvoltage. Select fault conditions can be set for ...

Circuit 

 

LTM4641 Negative Output Application. Delivering –5.2VOUT at Up to 10A, from Up to 32.8VIN

Oct 15th 2012
The LTM®4641 is a switch mode step-down DC/DC μModule® (micromodule) regulator with advanced input and load protection features. Trip detection thresholds for the following faults are customizable: input undervoltage, overtemperature, input overvoltage and output overvoltage. Select fault conditions can be set for ...

Circuit 

 

LT6110 with Internal RSENSE and LT3975 Buck Regulator at 3.3V

Jul 13th 2012
The LT®6110 is a precision high side current sense with a current mode output, designed for controlling the output voltage of an adjustable power supply or voltage regulator. This can be used to compensate for drops in voltage at a remote load due to resistance in a wire, trace or cable. The LT6110 monitors load current ...

Circuit 

 

12V, 10A Load Share

May 14th 2012
The LTC4370 is a two-supply current sharing controller which incorporates MOSFET ideal diodes. The diodes block reverse and shoot-through currents during start-up and fault conditions. Their forward voltage is adjusted to share the load currents between supplies. Unlike other sharing methods, neither a share bus nor trim pins ...

Circuit 

 

LTC2960 Li-Ion Battery and Regulator Monitor

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout period ...

Circuit 

 

LTC2960 Window Comparator for High Voltage Input

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout period ...

Circuit 

 

LTC2960 Battery Disconnect to Protect Against Deep Discharge

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout period ...

Circuit 

 

LTC2960 Micropower Power Supply Sequencer and Supervisor

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout period ...

Circuit 

 

LTC2960 Automotive Supervisor

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout period ...

Circuit 

 

Overvoltage Regulator with 250V Surge Protection

Dec 20th 2011
The LT4363 surge stopper protects loads from high voltage transients. It regulates the output during an overvoltage event, such as load dump in vehicles, by controlling the gate of an external N-channel MOSFET. The output is limited to a safe value allowing the loads to continue functioning. The LT4363 also monitors the voltage ...

Circuit LTspice 

 

28V Vehicle Application with Reverse Voltage Protection

Dec 14th 2011
The LTC4366 surge stopper protects loads from high voltage transients. By controlling the gate of an external N-channel MOSFET, the LTC4366 regulates the output during an overvoltage transient. The load may remain operational while the overvoltage is dropped across the MOSFET. Placing a resistor in the return line isolates the ...

Circuit 

 

Too many results please adjust your filters