1. Skip to navigation
  2. Skip to content
  3. Skip to sidebar

Solutions Search - LTC6078 - Micropower Precision, Dual CMOS Rail-to-Rail Input/Output Amplifiers

LTC6078 60Hz Notch Filter

Aug 16th 2005
High input impedance amplifiers are ideal for buffering high impedance networks. Here a twin-T notch filter is shown to reject 60Hz signal content by more the 60dB. Small size, low valued capacitors can be used at such a low frequency with high valued resistors when using a CMOS op amp. ...

Circuit LTspice 

 

LTC6078 Precision Ground Referenced Voltage Controlled Current Source

Aug 16th 2005
The control voltage, Vin, is converted to a charge on a capacitor that is referenced to ground. This charge is transferred to place a differential voltage across the output current programming resistor. The output current then flows into a ground referenced load for a precision single supply circuit without the need for a voltage ...

Circuit 

 

2.7V to 5.5V Precision High Side Current Sense

Aug 16th 2005
This high side current sense amplifier works down to 2.7V. Even with such a low supply voltage, accuracy of the voltage sensed across resistor Rs is preserved due to the very low voltage offset error of the LTC6078 amplifier (7uV typical). ...

Circuit 

 

0°C to 100°C Linear RTD Amplifier with 90°C Overtemperature Alarm

Aug 16th 2005
The LTC6078 is a dual, low offset, low noise operational amplifiers with low power consumption and rail-to-rail input/output swing. Input offset voltage is trimmed to less than 25μV and the CMOS inputs draw less than 50pA of bias current. The low offset drift, excellent CMRR, and high voltage gain make it a good choice for ...

Circuit 

 

LTC6078 pH Probe Amplifier

Aug 16th 2005
pH Probe amplifiers require buffer amplifiers with an input impedance greater than 10^13 ohms. Without loading the probe, an output of approximately 60mV/pH unit is produce. The thermistor is added to provide first order compensation for the inherent temperature coefficient of the pH probe output. ...

Circuit LTspice 

 

Reduced Power Infra-Red Diode Driver

Aug 16th 2005
Infra-Red LEDs can be used as continuously operating beams of light. Sensing a break in the path of light between the source and a photodiode receiver is often used in safety and alarm systems. To extend the run-time of the light source, the diode conducts the minimum current necessary, in this case 10mA. Controlling the duty ...

Circuit 

 

Type K Thermocouple Signal Conditioner with ±190V Protection from Accidental Contact and Cold Junction Compensation

Aug 16th 2005
Thermocouple wires are intended to be electrically floating in order to detect temperature by producing the Seebeck voltage created by two dissimilar metals. This small voltage is amplified to an easily measurable level by an amplifier. To protect the input terminals of the amplifier in the event that the thermocouple is shorted ...

Circuit 

 

Accelerometer Signal Conditioner

Aug 16th 2005
A piezoelectric accelerometer responds to any physical movement by generating a charge proportional to the acceleration of the movement. This sensor has a capacitance of 750pF which produces a charge of 60pC per g of gravitational force. This charge is transferred to the 1000pF feedback capacitor for an output of 60mV/g. ...

Circuit 

 

Thermocouple Thermometer with Cold Junction Compensation

Aug 16th 2005
The LTC2997 is a high-accuracy analog output temperature sensor. It converts the temperature of an external sensor or its own temperature to an analog voltage output. A built-in algorithm eliminates errors due to series resistance between the LTC2997 and the sensor diode. ...

Circuit 

 

Micropower Photodiode Amplifier

Aug 16th 2005
This is a basic photodiode amplifier which converts the tiny current output by the diode in response to light intensity to a buffered low impedance voltage source. CMOS amplifier's allow for the use of large feedback resistors and add very little input bias error current. For this Infra-Red diode the output changes 600mV for ...

Circuit 

 

Precision Sample and Hold Amplifier

Sep 3rd 2004
CMOS amplifiers are very good for use in Sample-and-Hold circuits because the pA's of bias current does not drain off charge held on the hold capacitor. A dual amplifier can be used to buffer the input signal and also the hold capacitor. The slew rate of the circuit is limited by the output current limit of the input amplifier ...

Circuit 

 

Paralleled Voltage Regulators with Balanced Load Sharing

Jul 15th 1999
Paralleling voltage regulators to provide mode load current is a common technique. Forcing the amplifiers to share the load current equally is called ballasting. Using a precision low offset voltage amplifier to sense the output current from each regulator requires just milli-ohms of resistance, typically just a pcb circuit ...

Circuit 

 

DC Accurate Composite Amplifier

Apr 1st 1992
Most individual op amp devices are optimized for either DC precision or for high speed operation. A composite amplifier configuration uses a precision low offset and drift amplifier to control the dc biasing of a high speed amplifier. This circuit has a gain bandwidth product of 1.25MHz yet an input offset voltage of only 25uV ...

Circuit