1. Skip to navigation
  2. Skip to content
  3. Skip to sidebar

Solutions Search - LED Driver Solutions

DC2286A - LT3932 Demo Board | VIN = 8V to 36V driving two series LEDs (1ALED/6.6VLED) at 2MHz

Oct 27th 2017
Demonstration circuit DC2286A is a 36V, 2A synchronous 2MHz buck LED driver featuring the LT3932. It drives one or two series LEDs at 1A when VIN is between 8V and 36V. It can run down to 4VIN with a single LED (if UVLO is adjusted). DC2286A runs at 2MHz switching frequency. Spread spectrum frequency modulation (SSFM) can be ...

Demo Board 

 

LTC6258 LED Driver with Self-Oscillation

Aug 30th 2017
The circuit above combines edge detection with use of the shutdown pin of the LTC6259. R2 and R3 bring in a divided down copy of the supply voltage as a reference into the positive terminal. The op amp forces this voltage on the sense resistor RSENSE in “LED ON” operation. In that sense this circuit is similar to ...

Circuit LTspice 

 

LTC6258 Lower Power LED Driver with Voltage Command

Aug 30th 2017
Figure above shows a voltage controlled LED drive circuit. When VIN is at 0V, the op amp supply current is nominally 20μA. The offset, for example, could be 450µV, appears across R1, inducing a 0.45mA current in the LED. Some applications want a guaranteed zero LED current at VIN = 0, and this is the purpose of R5. ...

Circuit LTspice 

 

DC2424A - LT3964 Demo Board | VIN = 5V to 36V driving two separate LED strings (1ALED/~3.6VLED) at 2MHz

Aug 22nd 2017
The DC2424A is a 36V synchronous dual LED driver with I 2C featuring the LT®3964. It drives two separate LEDs (or channels of LEDs) at 1A when VIN is between 5V and 36V. DC2424A runs at 2MHz switching frequency. Its two channels can drive separate LED strings which can have different currents, voltages, or dimming ratios. ...

Demo Board 

 

Hybrid Wide Dimming Ratio Linear LED Current Controller Using LT8614 & LT3083/LT6015

Tom Mosteller - Field Applications Engineer Oct 17th 2016
Many applications for LED illumination require wide dimming ratios. This can be accomplished simply via an adjustable current source as show below.  The current source can be varied by a number of different means, and a large LED current range can be achieved. The primary problem with this technique is that the power dissipation ...

Blog Post Circuit LTspice 

 

LT3598 LED Driver for 30 White LEDs with 60mA Each String

Oct 5th 2016
The LT3598 is a fixed frequency step-up DC/DC converter designed to drive up to six strings of LEDs at an output voltage up to 44V. LED dimming can be achieved with analog dimming on the CTRL pin, and with pulse width modulation dimming on the PWM pin. The LT3598 accurately regulates LED current even when the input voltage is ...

Circuit 

 

LT3598 Auto Battery Powered Driver for 20 LEDs with 90mA Each String

Oct 5th 2016
The LT3598 is a fixed frequency step-up DC/DC converter designed to drive up to six strings of LEDs at an output voltage up to 44V. LED dimming can be achieved with analog dimming on the CTRL pin, and with pulse width modulation dimming on the PWM pin. The LT3598 accurately regulates LED current even when the input voltage is ...

Circuit 

 

LT3598 2MHz LED Driver for 20 White LEDs

Oct 5th 2016
The LT3598 is a fixed frequency step-up DC/DC converter designed to drive up to six strings of LEDs at an output voltage up to 44V. LED dimming can be achieved with analog dimming on the CTRL pin, and with pulse width modulation dimming on the PWM pin. The LT3598 accurately regulates LED current even when the input voltage is ...

Circuit 

 

LT3598 1 MHz LED Driver for 36 White LEDs

Oct 5th 2016
The LT3598 is a fixed frequency step-up DC/DC converter designed to drive up to six strings of LEDs at an output voltage up to 44V. LED dimming can be achieved with analog dimming on the CTRL pin, and with pulse width modulation dimming on the PWM pin. The LT3598 accurately regulates LED current even when the input voltage is ...

Circuit 

 

LT3598 90% Efficient LED Driver for 60 White LEDs

Oct 5th 2016
The LT3598 is a fixed frequency step-up DC/DC converter designed to drive up to six strings of LEDs at an output voltage up to 44V. LED dimming can be achieved with analog dimming on the CTRL pin, and with pulse width modulation dimming on the PWM pin. The LT3598 accurately regulates LED current even when the input voltage is ...

Circuit 

 

LT3591 24V to Four White LEDs at 100mA

Oct 5th 2016
The LT3591 is a fixed frequency step-up DC/DC converter specifi cally designed to drive up to ten white LEDs in series from a Li-Ion cell. Series connection of the LEDs provides identical LED currents resulting in uniform brightness and eliminating the need for ballast resistors. The device features a unique high side LED current ...

Circuit 

 

LT3591 Li-Ion Driver for Seven White LEDs

Oct 5th 2016
The LT3591 is a fixed frequency step-up DC/DC converter specifi cally designed to drive up to ten white LEDs in series from a Li-Ion cell. Series connection of the LEDs provides identical LED currents resulting in uniform brightness and eliminating the need for ballast resistors. The device features a unique high side LED current ...

Circuit 

 

LT3591 Li-Ion Driver for Nine White LEDs

Oct 5th 2016
The LT3591 is a fixed frequency step-up DC/DC converter specifi cally designed to drive up to ten white LEDs in series from a Li-Ion cell. Series connection of the LEDs provides identical LED currents resulting in uniform brightness and eliminating the need for ballast resistors. The device features a unique high side LED current ...

Circuit 

 

LT3080 Low Dropout Voltage LED Driver

Sep 15th 2016
The LT3080 is a 1.1A low dropout linear regulator that can be paralleled to increase output current or spread heat in surface mounted boards. Architected as a precision current source and voltage follower allows this new regulator to be used in many applications requiring high current, adjustability to zero, and no heat sink. ...

Circuit 

 

LT3090 500mA LED Driver with Grounded LED Tab (Heatsink)

Sep 15th 2016
The LT®3090 is a 600mA, low dropout negative linear regulator that is easily parallelable to increase output current or spread heat on surface mounted boards. Designed with a precision current reference followed by a high performance rail-to-rail voltage buffer, this regulator finds use in applications requiring precision ...

Circuit 

 

LT3065 LED Driver/Current Source

Sep 15th 2016
The LT®3065 Series are micropower, low noise, low dropout voltage (LDO) linear regulators that operate over a 1.8V to 45V input voltage range. The devices supply 500mA of output current with a typical dropout voltage of 300mV. A single external capacitor provides programmable low noise reference performance and output soft-start ...

Circuit 

 

LT3085 Low Dropout Voltage LED Driver

Sep 15th 2016
The LT3085 is a 500mA low dropout linear regulator that can be paralleled to increase output current or spread heat on surface mounted boards. Designed as a precision current source and voltage follower, this new regulator finds use in many applications requiring high current, adjustability to zero, and no heat sink. The device ...

Circuit 

 

LT3517 Buck Mode 1A LED Driver

Sep 13th 2016
The LT3517 is a current mode DC/DC converter with an internal 1.5A, 45V switch specifically designed to drive LEDs. The LT3517 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3517 Low Side current Sensing Load Dump Protected Buck-Boost Mode LED Driver

Sep 13th 2016
The LT3517 is a current mode DC/DC converter with an internal 1.5A, 45V switch specifically designed to drive LEDs. The LT3517 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3517 Boost 100mA LED Driver with LED Open Protection

Sep 13th 2016
The LT3517 is a current mode DC/DC converter with an internal 1.5A, 45V switch specifically designed to drive LEDs. The LT3517 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3465 Li-Ion to Five White LEDs

Sep 12th 2016
The LT3465/LT3465A are step-up DC/DC converters designed to drive up to six LEDs in series from a Li-Ion cell. Series connection of the LEDs provides identical LED currents and eliminates the need for ballast resistors. These devices integrate the Schottky diode required externally on competing devices. Additional features include ...

Circuit 

 

LT3465 Li-Ion to Six White LEDs

Sep 12th 2016
The LT3465/LT3465A are step-up DC/DC converters designed to drive up to six LEDs in series from a Li-Ion cell. Series connection of the LEDs provides identical LED currents and eliminates the need for ballast resistors. These devices integrate the Schottky diode required externally on competing devices. Additional features include ...

Circuit 

 

LTC3200 Lithium-Ion Battery to 5V White or Blue LED Driver

Sep 12th 2016
A new charge-pump architecture maintains constant switching frequency to zero load and reduces bith output and input ripple. The LTC3200/LTC3200-5 have thermal shutdown capability and can survive a continuous short-circuit from VOUT to GND. Built-in soft-start circuitry prevents excessive inrush curreent during start-up. ...

Circuit 

 

LT3486 1 Li-Ion Cell to Dual 8 White LEDs

Sep 12th 2016
The LT3486 is a dual step-up DC/DC converter specifically designed to drive up to 16 White LEDs (8 in series per converter) at constant current from a single Li-Ion cell. Series connection of the LEDs provides identical LED currents resulting in uniform brightness. The two independent converters are capable of driving asymmetric ...

Circuit 

 

LT3486 5V to Dual 16 White LEDs @ 25mA

Sep 12th 2016
The LT3486 is a dual step-up DC/DC converter specifically designed to drive up to 16 White LEDs (8 in series per converter) at constant current from a single Li-Ion cell. Series connection of the LEDs provides identical LED currents resulting in uniform brightness. The two independent converters are capable of driving asymmetric ...

Circuit 

 

LT3486 12V to Dual 8 White LEDs @ 100mA

Sep 12th 2016
The LT3486 is a dual step-up DC/DC converter specifically designed to drive up to 16 White LEDs (8 in series per converter) at constant current from a single Li-Ion cell. Series connection of the LEDs provides identical LED currents resulting in uniform brightness. The two independent converters are capable of driving asymmetric ...

Circuit 

 

LT3476 5V to 25V Buck-Boost Mode Driver for 2 Series 350mA LEDs

Sep 12th 2016
The LT3476 is a quad output DC/DC converter designed to operate as a constant-current source for driving high current LEDs. A fixed frequency, current mode architecture results in stable operation over a wide range of supply and output voltages. A frequency adjust pin allows the user to program switching frequency between ...

Circuit 

 

LT3476 Buck Mode 100W Quad 1A × 8 LED Driver

Sep 12th 2016
The LT3476 is a quad output DC/DC converter designed to operate as a constant-current source for driving high current LEDs. A fixed frequency, current mode architecture results in stable operation over a wide range of supply and output voltages. A frequency adjust pin allows the user to program switching frequency between 200kHz ...

Circuit 

 

LT3476 Quad Boost 200mA × 8LED Driver

Sep 12th 2016
The LT3476 is a quad output DC/DC converter designed to operate as a constant-current source for driving high current LEDs. A fixed frequency, current mode architecture results in stable operation over a wide range of supply and output voltages. A frequency adjust pin allows the user to program switching frequency between 200kHz ...

Circuit 

 

LT3599 12W LED Driver 1MHz Boost, 80mA per String, 10 LEDs per String

Sep 9th 2016
The LT3599 is a fixed frequency 2A step-up DC/DC converter designed to drive four strings of 120mA LEDs up to a 44V output voltage. The switching frequency is programmable from 200kHz to 2.1MHz through an external resistor. ...

Circuit 

 

LT3599 12W LED Driver 400kHz Boost, Two LED Strings, 200mA per String, 8 LEDs per String

Sep 9th 2016
The LT3599 is a fixed frequency 2A step-up DC/DC converter designed to drive four strings of 120mA LEDs up to a 44V output voltage. The switching frequency is programmable from 200kHz to 2.1MHz through an external resistor. ...

Circuit 

 

LT3599 7W LED Driver SEPIC (Survives Output Short to Ground) 300kHz, Three Strings, 100mA per String, 6 LEDs per String

Sep 9th 2016
The LT3599 is a fixed frequency 2A step-up DC/DC converter designed to drive four strings of 120mA LEDs up to a 44V output voltage. The switching frequency is programmable from 200kHz to 2.1MHz through an external resistor. ...

Circuit 

 

LT3599 8W LED Driver 2MHz Boost, Three Strings, 100mA per String, 7 LEDs per String

Sep 9th 2016
The LT3599 is a fixed frequency 2A step-up DC/DC converter designed to drive four strings of 120mA LEDs up to a 44V output voltage. The switching frequency is programmable from 200kHz to 2.1MHz through an external resistor. ...

Circuit 

 

LT3599 2.1 MHz Boost, Four Strings, 80mA per String, 7 LEDs per String

Sep 9th 2016
The LT3599 is a fixed frequency 2A step-up DC/DC converter designed to drive four strings of 120mA LEDs up to a 44V output voltage. The switching frequency is programmable from 200kHz to 2.1MHz through an external resistor. ...

Circuit 

 

LTC3112 10W, 10V High Intensity LED Driver with Programmable Current and Low-Loss Sensing

Sep 9th 2016
The LTC®3112 is a fixed frequency synchronous buck-boost DC/DC converter with an extended input and output range. The unique 4-switch, single inductor architecture provides low noise and seamless operation from input voltages above, below or equal to the output voltage. ...

Circuit 

 

LTC3114-1 Constant Current High Brightness LED Driver

Sep 9th 2016
The LTC®3114-1 is a versatile, wide operating voltage range synchronous monolithic buck-boost DC/DC converter with programmable average output current. The LTC3114-1’s proprietary buck-boost PWM control circuitry delivers low noise operation across the entire operating voltage range. Current mode control ensures exceptional ...

Circuit 

 

LT3744 Boost Mode 3A LED Driver with 98% Efficiency

Sep 9th 2016
The LT®3744 is a fixed frequency synchronous step-down DC/DC controller designed to drive a LED load at up to 20A continuous or 40A pulsed. The peak current mode controller will maintain ±3% LED current regulation over a wide output voltage range, from VEE to VIN. By allowing VEE to float to negative voltages, several ...

Circuit 

 

LT3474 Step-Down 1A LED Driver with PWM Dimming

Sep 9th 2016
The LT3474/LT3474-1 are fixed frequency step-down DC/DC converters designed to operate as constant-current sources. An internal sense resistor monitors the output current allowing accurate current regulation, ideal for driving high current LEDs. High output current accuracy is maintained over a wide current range, from 35mA ...

Circuit 

 

LT3474 Step-Down 1A LED Driver with Two Series Connected LED Output

Sep 9th 2016
The LT3474/LT3474-1 are fixed frequency step-down DC/DC converters designed to operate as constant-current sources. An internal sense resistor monitors the output current allowing accurate current regulation, ideal for driving high current LEDs. High output current accuracy is maintained over a wide current range, from 35mA ...

Circuit 

 

LT3474 Step-Down 1A LED Driver with Four Series Connected LED Output

Sep 9th 2016
The LT3474/LT3474-1 are fixed frequency step-down DC/DC converters designed to operate as constant-current sources. An internal sense resistor monitors the output current allowing accurate current regulation, ideal for driving high current LEDs. High output current accuracy is maintained over a wide current range, from 35mA ...

Circuit 

 

LT8611 2A LED Driver

Sep 9th 2016
The LT®8611 is a compact, high efficiency, high speed synchronous monolithic step-down switching regulator that consumes only 2.5μA of quiescent current. Top and bottom power switches are included with all necessary circuitry to minimize the need for external components. The built-in current sense amplifier with monitor ...

Circuit 

 

LT3478 15W, 6 LEDs at 700mA, Boost LED Driver

Sep 9th 2016
The LT3478-1 reduces external component count and cost by integrating the LED current sense resistor. The LT3478 uses an external sense resistor to extend the maximum programmable LED current beyond 1A and also to achieve greater accuracy when programming low LED currents. Operating frequency can be set with an external resistor ...

Circuit 

 

LT3478 17W, 15 LEDs at 350mA, Boost LED Driver plus LT3003

Sep 9th 2016
The LT3478-1 reduces external component count and cost by integrating the LED current sense resistor. The LT3478 uses an external sense resistor to extend the maximum programmable LED current beyond 1A and also to achieve greater accuracy when programming low LED currents. Operating frequency can be set with an external resistor ...

Circuit 

 

LT3478 16W, 12 LEDs at 350mA, Buck-Boost Mode LED Driver plus LT3003

Sep 9th 2016
The LT3478-1 reduces external component count and cost by integrating the LED current sense resistor. The LT3478 uses an external sense resistor to extend the maximum programmable LED current beyond 1A and also to achieve greater accuracy when programming low LED currents. Operating frequency can be set with an external resistor ...

Circuit 

 

LT3478 4W, 1 LED at 1A, Buck-Boost Mode LED Driver

Sep 9th 2016
The LT3478-1 reduces external component count and cost by integrating the LED current sense resistor. The LT3478 uses an external sense resistor to extend the maximum programmable LED current beyond 1A and also to achieve greater accuracy when programming low LED currents. Operating frequency can be set with an external resistor ...

Circuit 

 

LT3478 24W, 4 LEDs at 1.5A, Buck Mode LED Driver

Sep 9th 2016
The LT3478-1 reduces external component count and cost by integrating the LED current sense resistor. The LT3478 uses an external sense resistor to extend the maximum programmable LED current beyond 1A and also to achieve greater accuracy when programming low LED currents. Operating frequency can be set with an external resistor ...

Circuit 

 

LT3478 6W, 6 LEDs at 250mA, Boost LED Driver

Sep 9th 2016
The LT3478-1 reduces external component count and cost by integrating the LED current sense resistor. The LT3478 uses an external sense resistor to extend the maximum programmable LED current beyond 1A and also to achieve greater accuracy when programming low LED currents. Operating frequency can be set with an external resistor ...

Circuit 

 

LT3795 Short-Circuit Robust Boost LED Driver with Input Current Limit and Spread Spectrum Frequency Modulation

Sep 8th 2016
The LT®3795 is a DC/DC controller designed to regulate a constant-current or constant-voltage and is ideal for driving LEDs. It drives a low side external N-channel power MOSFET from an internal regulated 7.7V supply. The fixed frequency and current mode architecture result in stable operation over a wide range of supply ...

Circuit 

 

LT3795 SEPIC LED Driver with Input Current Limit

Sep 8th 2016
The LT®3795 is a DC/DC controller designed to regulate a constant-current or constant-voltage and is ideal for driving LEDs. It drives a low side external N-channel power MOSFET from an internal regulated 7.7V supply. The fixed frequency and current mode architecture result in stable operation over a wide range of supply ...

Circuit 

 

LT3795 Buck Mode LED Driver

Sep 8th 2016
The LT®3795 is a DC/DC controller designed to regulate a constant-current or constant-voltage and is ideal for driving LEDs. It drives a low side external N-channel power MOSFET from an internal regulated 7.7V supply. The fixed frequency and current mode architecture result in stable operation over a wide range of supply ...

Circuit 

 

LT3795 Buck Mode LED Driver with 3000:1 PWM Dimming

Sep 8th 2016
The LT®3795 is a DC/DC controller designed to regulate a constant-current or constant-voltage and is ideal for driving LEDs. It drives a low side external N-channel power MOSFET from an internal regulated 7.7V supply. The fixed frequency and current mode architecture result in stable operation over a wide range of supply ...

Circuit 

 

LT3518 Buck Mode 1.5A LED Driver

Sep 8th 2016
The LT3518 is a current mode DC/DC converter with an internal 2.3A, 45V switch specifically designed to drive LEDs. The LT3518 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3518 Buck-Boost Mode LED Driver

Sep 8th 2016
The LT3518 is a current mode DC/DC converter with an internal 2.3A, 45V switch specifically designed to drive LEDs. The LT3518 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3518 Buck Mode 1A LED Driver with Open LED Protection and Sync Input

Sep 8th 2016
The LT3518 is a current mode DC/DC converter with an internal 2.3A, 45V switch specifically designed to drive LEDs. The LT3518 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3518 Boost 300mA LED Driver with LED Open Protection

Sep 8th 2016
The LT3518 is a current mode DC/DC converter with an internal 2.3A, 45V switch specifically designed to drive LEDs. The LT3518 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3755 20W SEPIC LED Driver

Sep 6th 2016
The LT3755, LT3755-1 and LT3755-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3755 Buck Mode 1.4A LED Driver

Sep 6th 2016
The LT3755, LT3755-1 and LT3755-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3755 Buck Mode 500mA LED Driver for 20kHz PWM Dimming

Sep 6th 2016
The LT3755, LT3755-1 and LT3755-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3755 21W Buck-Boost Mode with 250:1 PWM Dimming and Open LED Protection

Sep 6th 2016
The LT3755, LT3755-1 and LT3755-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3755 Buck-Boost LED Driver for Automotive

Sep 6th 2016
The LT3755, LT3755-1 and LT3755-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3756 30W White LED Headlamp Driver with Thermal Derating

Sep 6th 2016
The LT3756, LT3756-1 and LT3756-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current-mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3756 Buck-Boost Mode LED Driver

Sep 6th 2016
The LT3756, LT3756-1 and LT3756-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current-mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3756 90% Efficient, 20W SEPIC LED Driver

Sep 6th 2016
The LT3756, LT3756-1 and LT3756-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current-mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3756 Buck Mode 1A LED Driver with High Dimming Ratio and Open LED Reporting

Sep 6th 2016
The LT3756, LT3756-1 and LT3756-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current-mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3741 20A LED Driver

Sep 6th 2016
The LT®3741 and LT3741-1 are fixed frequency synchronous step-down DC/DC controllers designed to accurately regulate the output current at up to 20A. The average currentmode controller will maintain inductor current regulation over a wide output voltage range of 0V to (VIN – 2V). The regulated current is set by an ...

Circuit 

 

LTM8040 Step Down 1A Drive with Single Red or White LED

Sep 2nd 2016
The LTM8040 is a fixed frequency 1A step-down DC/DC μModule (power module) regulator designed to operate as a constant current source. Internal circuitry monitors the output current to provide accurate current regulation, which is ideal for driving high current LEDs. High output current accuracy is maintained over a wide ...

Circuit 

 

LTM8040 Step Down 350mA Drive with Three Series Red LEDs

Sep 2nd 2016
The LTM8040 is a fixed frequency 1A step-down DC/DC μModule (power module) regulator designed to operate as a constant current source. Internal circuitry monitors the output current to provide accurate current regulation, which is ideal for driving high current LEDs. High output current accuracy is maintained over a wide ...

Circuit 

 

LTM8040 Step Down 1A Drive with Four Series Red LEDs

Sep 2nd 2016
The LTM8040 is a fixed frequency 1A step-down DC/DC μModule (power module) regulator designed to operate as a constant current source. Internal circuitry monitors the output current to provide accurate current regulation, which is ideal for driving high current LEDs. High output current accuracy is maintained over a wide ...

Circuit 

 

LTM8042 Boost Operation, Driving 6 White LEDs at 1A

Sep 2nd 2016
The LTM8042 is a complete μModule (power module) Boost LED Driver specifically designed to drive LEDs up to 1A, while the LTM8042-1 drives up to 350mA. It combines a boost power topology with a unique current loop to operate as a constant-current source. The PWM input provides as much as 3000:1 LED dimming, while 10:1 analog ...

Circuit 

 

LTM8042 Boost Operation, Driving 9 White LEDs at 100mA

Sep 2nd 2016
The LTM8042 is a complete μModule (power module) Boost LED Driver specifically designed to drive LEDs up to 1A, while the LTM8042-1 drives up to 350mA. It combines a boost power topology with a unique current loop to operate as a constant-current source. The PWM input provides as much as 3000:1 LED dimming, while 10:1 analog ...

Circuit 

 

LTM8042 Buck-Boost Mode, Driving 5 White LEDs at 500mA with PWM Dimming

Sep 2nd 2016
The LTM8042 is a complete μModule (power module) Boost LED Driver specifically designed to drive LEDs up to 1A, while the LTM8042-1 drives up to 350mA. It combines a boost power topology with a unique current loop to operate as a constant-current source. The PWM input provides as much as 3000:1 LED dimming, while 10:1 analog ...

Circuit 

 

LTM8042 Buck Mode, Driving 4 White LEDs at 1A

Sep 2nd 2016
The LTM8042 is a complete μModule (power module) Boost LED Driver specifically designed to drive LEDs up to 1A, while the LTM8042-1 drives up to 350mA. It combines a boost power topology with a unique current loop to operate as a constant-current source. The PWM input provides as much as 3000:1 LED dimming, while 10:1 analog ...

Circuit 

 

LTM8042 Boost Operation, Driving 9 Red LEDs at 350mA with Analog Dimming

Sep 2nd 2016
The LTM8042 is a complete μModule (power module) Boost LED Driver specifically designed to drive LEDs up to 1A, while the LTM8042-1 drives up to 350mA. It combines a boost power topology with a unique current loop to operate as a constant-current source. The PWM input provides as much as 3000:1 LED dimming, while 10:1 analog ...

Circuit 

 

LT3965 Matrix LED Dimmer Powered by a Dual Buck Mode LED Driver with a Boost Pre-Regulator

Sep 2nd 2016
The LT®3965 is an LED bypass switching device for dimming individual LEDs in a string using a common current source. It features eight individually controlled floating source 17V/330mΩ NMOS switches. The eight switches can be connected in parallel and/or in series to bypass current around one or more LEDs in a string. ...

Circuit 

 

LT3965 Matrix LED Dimmer Powered by a Boost-Buck LED Driver

Sep 2nd 2016
The LT®3965 is an LED bypass switching device for dimming individual LEDs in a string using a common current source. It features eight individually controlled floating source 17V/330mΩ NMOS switches. The eight switches can be connected in parallel and/or in series to bypass current around one or more LEDs in a string. ...

Circuit 

 

LT8391 98% Efficient 50W (25V 2A) Buck-Boost LED Driver

Sep 2nd 2016
The LT®8391 is a synchronous 4-switch buck-boost LED controller that regulates LED current from input voltage above, below, or equal to the output voltage. The proprietary peak-buck peak-boost current mode control scheme allows adjustable and synchronizable 150kHz to 650kHz fixed frequency operation, or internal ±15% ...

Circuit 

 

LT8391 95% Efficient 12W (12V 1A) Buck-Boost LED Driver with Dual Package MOSFETs

Sep 2nd 2016
The LT®8391 is a synchronous 4-switch buck-boost LED controller that regulates LED current from input voltage above, below, or equal to the output voltage. The proprietary peak-buck peak-boost current mode control scheme allows adjustable and synchronizable 150kHz to 650kHz fixed frequency operation, or internal ±15% ...

Circuit Press Release 

 

LT8391 98% Efficient 100W (33.3V 3A) Buck-Boost LED Driver

Sep 2nd 2016
The LT®8391 is a synchronous 4-switch buck-boost LED controller that regulates LED current from input voltage above, below, or equal to the output voltage. The proprietary peak-buck peak-boost current mode control scheme allows adjustable and synchronizable 150kHz to 650kHz fixed frequency operation, or internal ±15% ...

Circuit 

 

LT3763 20A, Pulse Width Modulated, Single LED Driver

Sep 2nd 2016
The LT3763 is a fixed frequency, synchronous, step-down DC/DC controller designed to accurately regulate output currents up to 20A. The average current mode control- ler will maintain inductor current regulation over a wide output voltage range from 0V to 55V. Output current is set by analog voltages on the CTRL pins and an ...

Circuit 

 

LT3763 1A, Five LED Driver

Sep 2nd 2016
The LT3763 is a fixed frequency, synchronous, step-down DC/DC controller designed to accurately regulate output currents up to 20A. The average current mode control- ler will maintain inductor current regulation over a wide output voltage range from 0V to 55V. Output current is set by analog voltages on the CTRL pins and an ...

Circuit 

 

Too many results please adjust your filters