1. Skip to navigation
  2. Skip to content
  3. Skip to sidebar

Solutions Search - Fully Differential Amplifiers

Converting a Low Distortion Single-Ended Sine Source to Fully Differential

Guy Hoover - Applications Engineer Sep 10th 2017
Customers looking for a way to evaluate ADCs with differential inputs will find themselves in need of a low distortion, low noise differential sine source. Single-ended sine sources can be obtained by building a simple Wien-bridge oscillator or by employing any of several readily available audio oscillators. Differential sine ...

Blog Post 

 

DC961B - LT1994 Low Noise, Low Distortion, Fully Differential Amplifier/Driver

Jun 28th 2017
Demonstration circuit 961 features an LT®1994, low noise, low distortion, fully differential amplifier. The LT1994 is a high precision, very low noise, low distortion, fully differential input/output amplifier (see Table 1). The LT1994’s output common mode voltage is independent of the input common mode voltage, and ...

Demo Board 

 

DC2623A - LTC6404-1 + AD8002 ADC Driver Board | Low Distortion ADC Driver for LTC2387 family, Input Frequencies >1MHz

Jun 16th 2017
Demonstration circuit 2623A features the LTC6404-1 amplifier. The DC2623A includes two of these amplifiers and is designed to drive the inputs of the DC2290 demo board. The DC2290 features the LTC2387 18-bit, 15Msps high speed SAR ADC. The linearity and low noise of the LTC6404-1 make it an ideal candidate to drive the LTC2387 ...

Demo Board 

 

15dB Gain Differential Amplifier Delivers up to +50dBm OIP3 Linearity and Low Noise from 100kHz to 1.4GHz

May 10th 2017
MILPITAS, CA and NORWOOD, MA – May 10, 2017 – Analog Devices, Inc., which recently acquired Linear Technology Corporation, announces the LTC6432-15, a wideband fully differential amplifier with 15dB gain, offering linearity of up to +50.3dBm OIP3 (output third-order intercept), very high OP1dB (output 1dB compression ...

Press Release 

 

Dual Differential Amplifier/ADC Driver Delivers 10GHz Gain Bandwidth with 1.1nV/√Hz Noise

Mar 22nd 2017
MILPITAS, CA & NORWOOD, MA – March 22, 2017 – Analog Devices, Inc., which recently acquired Linear Technology Corporation, announces the LTC6419, a dual 10GHz gain bandwidth product differential amplifier with very low input voltage noise density of 1.1nV/√Hz, delivering outstanding SNR performance for ...

Press Release 

 

DC2473A - LTC6419 - Dual Differential Amplifiers / ADC Drivers

Mar 15th 2017
Demonstration circuit 2473A features the LTC®6419 Dual Differential Amplifier/ADC Driver. It incorporates a variety of passive components to support configurations for varied applications. These fully-differential amplifiers accept single-ended or differential input with almost no difference in distortion performance. ...

Demo Board 

 

Improving Linearity by Using Absorptive Filters

Clarence Mayott - Applications Engineer Mar 10th 2017
Introduction: When driving a direct sampling high speed ADC, the most likely place to degrade the performance is the interface between the final amplifier and the ADC. With any direct sampling ADC there will be nonlinear charge produced in the sampling process. This charge is reflected into the input network each time the sampling ...

Blog Post 

 

High Linearity, Low Noise LTC2387-18 Drivers for Sinusoidal Signals

Doug Stuetzle - Senior Analog Applications Engineer Jan 10th 2017
Introduction The LTC2387-18 is a high speed SAR (Successive Approximation Register) ADC suited for high linearity, low noise applications. This ADC is capable of sampling at up to 15Msps, which allows it to convert signals at frequencies of several MHz. It is well-suited to convert both pulsed and continuous signals in this ...

Blog Post 

 

DC2487A - LTC6363 Rail-to-Rail SAR ADC Driver Amplifier

Jan 10th 2017
Demonstration circuit 2487A features the LTC®6363 amplifier. The DC2487A is designed to drive the inputs of the DC2290A demo board. The DC2290A features the LTC®2387 18-bit, 15Msps high speed SAR ADC. The linearity and low noise of the LTC6363 make it an ideal candidate to drive the LTC2387 at frequencies up to 100kHz. ...

Demo Board 

 

LTC2387 Drivers Part III: Trans-Impedance Amplifier/Driver

Derek Redmayne - Staff Scientist Sep 8th 2016
This is unabashedly a classic case of what marketing calls “a solution looking for a problem”. It is an example of how the full SNR of the LTC2387 may be realized for a real world signal. Most signals originating in low level circuitry, in sensors, or in the real world, will require significant gain to develop 8Vp-p ...

Blog Post 

 

Anti-Alias Filter for 24-bit ADC

Guy Hoover - Applications Engineer Aug 3rd 2016
For many ADC applications a simple RC filter at the buffer input will provide adequate anti-alias filtering. For applications that require a higher order filter an active filter is often used. The active component in that filter must have sufficient bandwidth, fast settling, low noise and low offset so that it doesn’t ...

Blog Post 

 

Baseband Design Example for LTC5589/LTC5599 Low-Power IQ Modulator

Bruce Hemp - Applications Section Leader Jul 1st 2016
Introduction This basic low power modulator was described in the LT Journal Nov 2015 article. In this blog post, we will show how to: Use simulation to validate the filter design, and Reduce DC offsets by utilizing Differential Amplifiers for the baseband drive. Also shown are some miscellaneous tips to help complete ...

Blog Post Circuit LTspice 

 

How to Drive the LTC2387 (Part 1): Signal Applications to 5MHz that Require Low Inter-Modulation Distortion

Derek Redmayne - Staff Scientist May 13th 2016
The biggest challenge in driving a 15Msps, 18-bit ADC with an 8Vp-p input range is the lack of integrated amplifiers with adequate bandwidth, low noise, and the required output excursion. There are low-noise, high-BW amplifiers than can produce 2VPP. There are low speed amplifiers than can produce 8VPP. For low distortion beyond ...

Blog Post 

 

DC2319A-A - LTC6363 Differential Op Amp/ADC Driver Demo Board

Nov 10th 2015
The LTC®6363 is a low power, low noise differential op amp with rail-to-rail output swing and good DC accuracy. The amplifier may be configured to process a fully differential input signal or to convert a single-ended input signal to a differential output signal. The differential outputs of the DC2319A can be configured ...

Demo Board 

 

Precision Differential Amplifier Drives 20-Bit ADCs Consuming Less than 2mA

Sep 24th 2015
MILPITAS, CA - September 24, 2015 - Linear Technology introduces the LTC6363, a low power, high precision, fully differential amplifier optimized for driving high performance 16-, 18- and 20-bit SAR and ΔΣ ADCs. Featuring 100µV maximum input offset voltage and 2.9nV/√Hz input-referred voltage noise, the LTC6363 consumes ...

Press Release 

 

Driving High Resolution SAR ADCs

Tyler Hutchison - Signal Conditioning Design Engineer Sep 8th 2015
Driving high resolution SAR ADCs often requires tradeoffs between power consumption, linearity, and noise.  The LTC6363 provides 20 bit accuracy when the system designer pays close attention to the interface filter between the driver and the ADC.  Calculations and empirical data provide additional insight as to how ...

Video 

 

LTC6363 LTC6363 Used as Lowpass Filter/Driver with 10VP-P Singled-Ended Input, Driving a SAR ADC

Aug 31st 2015
The LTC®6363 is a low power, low noise, fully differential op amp with rail-to-rail outputs optimized to drive low power SAR ADCs. The LTC6363 draws only 1.9mA supply current in active operation and features a shutdown mode which reduces the current consumption to 20μA (VS = 3V). ...

Circuit 

 

LTC6363 Differential AV = 1/9 Configuration Using an LT®5400 Quad-Matched Resistor Network

Aug 31st 2015
The LTC®6363 is a low power, low noise, fully differential op amp with rail-to-rail outputs optimized to drive low power SAR ADCs. The LTC6363 draws only 1.9mA supply current in active operation and features a shutdown mode which reduces the current consumption to 20μA (VS = 3V). ...

Circuit 

 

LTC6363 Single-Ended-to-Differential Conversion of a 20VP-P Ground-Referenced Input with Gain of AV = 0.5 to Drive an ADC

Aug 31st 2015
The LTC®6363 is a low power, low noise, fully differential op amp with rail-to-rail outputs optimized to drive low power SAR ADCs. The LTC6363 draws only 1.9mA supply current in active operation and features a shutdown mode which reduces the current consumption to 20μA (VS = 3V). ...

Circuit 

 

DC2266A - LTC2107 + LTC6409 Demo Board | 16-Bit, 210Msps ADC and Driver Combo Board, DC-100MHz Input, DDR LVDS Outputs, (req DC1371 and DC2219)

May 20th 2015
Demonstration circuit 2266A features the LTC®2107, 210Msps ADC, and the LTC6409 low noise amplifier. DC2266A supports the LTC2107 DDR LVDS output mode. The circuitry on the analog inputs is optimized for analog input frequencies from DC to 100MHz. When driven with a 50Ω source, the gain will be 6dB. To modify the ...

Demo Board LinearLabTools PScope 

 

LTspice: SAR ADC Driver Interface

Kris Lokere - Strategic Applications Manager Apr 3rd 2014
High-performance SAR ADCs can offer amazing dynamic range and linearity at faster and faster sample rates. But how do you design the amplifier and interface at the analog inputs? LTspice IV can help. This video shows how to use LTspice to simulate the analog input interface of high-performance SAR ADCs. We will look at charge ...

Blog Post Video LTspice 

 

Digital Gain Compression (DGC) for SAR ADCs

Mar 11th 2014
The LTC2378-20 offers a digital gain compression (DGC) feature which defines the full-scale input swing to be between 10% and 90% of the ±VREF analog input range. This feature allows the SAR ADC driver to be powered off of a single positive supply since each input swings between 0.5V and 4.5V as shown in the figure below. Needing ...

Blog Post 

 

Single-Ended to Differential Conversion Using Differential Op Amps

Kris Lokere - Strategic Applications Manager Jan 13th 2014
Differential op amps are important building blocks in modern analog and mixed signal circuits. Many modern ADCs require differential signals at the inputs. Differential analog signals are also handy to drive signals over a cable. Differential op amps are useful building blocks for creating differential signals. Linear Technology ...

Video 

 

DC1945A - LTC2185 and LTC6409 Combo Board with differential inputs, req DC890, LVDS_XFMR and DC1075

Jan 16th 2013
DC1945A - Demo Board for:LTC2185 - 16-Bit, 125Msps Low Power Dual ADCsLTC6409 - 10GHz GBW, 1.1nV/√Hz Differential Amplifier/ADC Driver ...

Demo Board PScope 

 

Low Noise (1.5nV/√Hz) Fully Differential 1.6GHz Buffer Drives 50Ohm Load

Aug 15th 2012
MILPITAS, CA – August 15, 2012 – Linear Technology announces the LTC6417, a fully differential buffer amplifier with only 1.5nV/√Hz output-referred noise. The LTC6417 is capable of driving a differential 50Ohm load and is optimized for driving 14- and 16-bit pipeline ADCs. It can be DC- or AC-coupled at its inputs, and ...

Press Release 

 

DC1805A-H - LTC6362 with 250ksps 18-bit LTC2376-18 SAR ADC, LTC6655-5. Req DC718 or DC2026

Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1805A-G - LTC6362 with 500ksps 18-bit LTC2377-18 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1805A-F - LTC6362 with 1Msps 18-bit LTC2378-18 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1805A-E - LTC6362 with 1.6Msps 18-bit LTC2379-18 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1805A-D - LTC6362 with 250ksps 16-bit LTC2376-16 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1805A-C - LTC6362 with 500ksps 16-bit LTC2377-16 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1660B - LTC6417 Demo Circuit 1.6GHz differential ADC buffer, drives 50 Ohm load

May 30th 2012
DC1660B - Demo Board for:LTC6417 - 1.6GHz Low Noise High Linearity Differential Buffer/16-Bit ADC Driver with Fast Clamp ...

Demo Board 

 

DC1805A-B - LTC6362 with 1Msps 16-bit LTC2378-16 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

May 17th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal. ...

Demo Board Linduino PScope QuikEval System 

 

DC1805A-A - LTC6362 with 2Msps 16-bit LTC2380-16 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026

May 16th 2012
DC1805A-A - Demo Board for:LTC2380-16 - 16-Bit, 2Msps, Low Power SAR ADC with 96dB SNRLTC6362 - Precision, Low Power Rail-to-Rail Input/Output Differential Op Amp/SAR ADC DriverLTC6655 - 0.25ppm Noise, Low Drift Precision References ...

Demo Board Linduino PScope QuikEval System 

 

DC1833A - LTC6362 | Precision Low Power Differential ADC Driver Demo Board

May 14th 2012
DC1833A - Demo Board for:LTC6362 - Precision, Low Power Rail-to-Rail Input/Output Differential Op Amp/SAR ADC Driver ...

Demo Board 

 

Fully Differential Amplifier Drives 18-bit ADCs & Consumes only 5mW

May 2nd 2012
MILPITAS, CA – May 2, 2012 – Linear Technology announces the LTC6362, a low power fully differential amplifier that can drive high precision 16- and 18-bit SAR ADCs at only 1mA supply current. With 200µV max input offset voltage and 3.9nV/√Hz input-referred noise, it is well suited for precision industrial and data acquisition applications. The ...

Press Release 

 

Matched Resistor Networks for Precision Amplifier Applications

Tyler Hutchison - Signal Conditioning Design Engineer May 1st 2012
Introduction Some ideal op amp configurations assume that the feedback resistors exhibit perfect matching. In practice, resistor non-idealities can affect various circuit parameters such as common mode rejection ratio (CMRR), harmonic distortion and stability. For instance, as shown in Figure 1, a single-ended amplifier configured ...

Blog Post 

 

DC1783A-H - LTC2376-18 with LTC6655-5/LT6350 Demo Board | 18-Bit, 250ksps, SAR ADC with 102dB SNR. Req DC718 or DC2026

Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

DC1783A-G - LTC2377-18 with LTC6655-5/LT6350 Demo Board | 18-Bit, 500ksps, SAR ADC with 102dB SNR. Req DC718 or DC2026

Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

DC1783A-F - LTC2378-18 with LTC6655-5/LT6350 Demo Board | 18-Bit, 1Msps, SAR ADC with 102dB SNR. Req DC718 or DC2026

Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

DC1783A-D - LTC2376-16 with LTC6655-5/LT6350 Demo Board | 16-Bit, 250ksps, SAR ADC with 97dB SNR. Req DC718 or DC2026

Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

DC1783A-C - LTC2377-16 with LTC6655-5/LT6350 Demo Board | 16-Bit, 500ksps, SAR ADC with 97dB SNR. Req DC718 or DC2026

Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

DC1783A-B - LTC2378-16 with LTC6655-5/LT6350 Demo Board | 16-Bit, 1Msps, SAR ADC with 97dB SNR. Req DC718 or DC2026

Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

DC1760A - LTC2261-14 + LTC6409 ADC and Driver Combo Board,DC-100MHz, CMOS Outputs, req DC890 and DC1075

Jun 8th 2011
DC1760A - Demo Board for:LTC2261-14 - 14-Bit, 125Msps Ultra-Low Power 1.8V ADCsLTC6409 - 10GHz GBW, 1.1nV/√Hz Differential Amplifier/ADC Driver ...

Demo Board PScope 

 

DC1783A-A - LTC2380-16 with LTC6655-5/LT6350 Demo Board | 16-Bit, 2Msps, SAR ADC with 96dB SNR. Req DC718 or DC2026A

Mar 23rd 2011
DC1783A-A - Demo Board for:LTC2380-16 - 16-Bit, 2Msps, Low Power SAR ADC with 96dB SNRLTC6655 - 0.25ppm Noise, Low Drift Precision ReferencesLT6350 - Low Noise Single-Ended to Differential Converter/ADC Driver ...

Demo Board Linduino PScope QuikEval System 

 

DC1783A-E - LTC2379-18 with LTC6655-5/LT6350 Demo Board | 18-Bit, 1.6Msps, SAR ADC with 101dB SNR. Req DC718 or DC2026

Mar 4th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...

Demo Board Linduino PScope QuikEval System 

 

DC1600A - LTC6412, LTC2261-14 | 10MHz to 800MHz, 31dB Range Analog Controlled VGA

Nov 15th 2010
DC1600A - Demo Board for:LTC6412 - 800MHz, 31dB Range Analog-Controlled VGA ...

Demo Board PScope 

 

DC1591A - LTC6409 | 10GHz, 1nV/rt(Hz) Differential Amplifier/ADC Driver

Oct 27th 2010
DC1591A - Demo Board for:LTC6409 - 10GHz GBW, 1.1nV/√Hz Differential Amplifier/ADC Driver ...

Demo Board 

 

Differential Amplifier Drives DC-Coupled, Ground-Referenced 100MHz Signals with Low Noise & Low Distortion

Oct 12th 2010
MILPITAS, CA - October 12, 2010 - Linear Technology introduces the LTC6409, a fully differential amplifier capable of driving DC to 100MHz signals with just 1.1nV/√Hz noise and -88dBc HD2/HD3 distortion. Built on an advanced SiGe BiCMOS process, the LTC6409 features 10GHz gain-bandwidth product, 100dB SFDR up to 40MHz, and ...

Press Release 

 

DC1538A - LT6350 demo board

Feb 22nd 2010
DC1538A - Demo Board for:LT6350 - Low Noise Single-Ended to Differential Converter/ADC Driver ...

Demo Board 

 

DC1500A-C - LTC2391-16 with LT6350 optimized driver, 5V 16-bit 250ksps Int Ref Parallel / Serial SAR ADC in LQFP-48, req DC718

Feb 22nd 2010
DC1500A-C - Demo Board for:LT6350 - Low Noise Single-Ended to Differential Converter/ADC DriverLTC2391-16 - 16-Bit, 250ksps SAR ADC with 94dB SNR ...

Demo Board PScope 

 

DC1500A-B - LTC2392-16 with LT6350 optimized driver, 5V 16-bit 500ksps Int Ref Parallel / Serial SAR ADC in LQFP-48, req DC718

Feb 22nd 2010
DC1500A-B - Demo Board for:LTC2392-16 - 16-Bit, 500ksps SAR ADC with 94dB SNRLT6350 - Low Noise Single-Ended to Differential Converter/ADC Driver ...

Demo Board PScope 

 

DC1500A-A - LTC2393-16 with LT6350 optimized driver, 5V 16-bit 1Msps Int Ref Parallel / Serial SAR ADC in LQFP-48, req DC718

Feb 22nd 2010
DC1500A-A - Demo Board for:LTC2393-16 - 16-Bit, 1Msps SAR ADC With 94dB SNR ...

Demo Board PScope 

 

Rail-to-Rail Single-Ended to Differential Amplifier Drives High Speed 16- to 18-bit SAR ADCs

Jan 25th 2010
MILPITAS, CA - January 25, 2010 - Linear Technology introduces the LT6350, a 33MHz, low noise, rail-to-rail input and output ADC driver that settles to 16-bits in just 350ns. It is suitable for driving the latest highest performance SAR ADCs such as the LTC2393-16. The LT6350 incorporates two op amps and matched resistors to ...

Press Release 

 

DC1257B - LTC6416 + LTC2208 Combo board (Requires DC890 & LVDS_XFMR)

Oct 21st 2009
DC1257B - Demo Board for:LTC6416 - 2GHz Low Noise Differential 16-Bit ADC Buffer ...

Demo Board PScope 

 

800MHz VGA with 31dB Analog Control Range Has 35dBm OIP3 from 3.3V Supply

Jul 14th 2009
MILPITAS, CA - July 14, 2009 - Linear Technology introduces the LTC6412, an 800MHz analog-controlled variable gain amplifier (VGA) with outstanding noise and distortion performance, gain conformance, and gain flatness. The device’s gain control is highly linear. With a guaranteed maximum conformance error of only 0.45dB, the ...

Press Release 

 

DC1464A - LTC6412 l 800 MHz, 31dB Range Analog-Controlled VGA

May 26th 2009
DC1464A - Demo Board for:LTC6412 - 800MHz, 31dB Range Analog-Controlled VGA ...

Demo Board 

 

DC1251A-B - LTC6601-2 | Low Power, Low Distortion Configurable Broadband Filter Demo Board

Apr 1st 2009
DC1251A-B - Demo Board for:LTC6601-2 - Low Power, Low Distortion, Low Power, Low Distortion, 5MHz to 27MHz, Pin Configurable Filter/ADC Driver ...

Demo Board 

 

Differential ADC Buffer Drives 300MHz Signals with Only 1.8nV/√Hz Noise

Mar 5th 2009
MILPITAS, CA - March 5, 2009 - Linear Technology introduces the LTC6416, a wideband unity gain 2GHz differential buffer aimed at addressing the challenge of driving high resolution ADCs. The LTC6416 provides excellent noise figure and distortion performance at high frequencies. With its programmable output voltage clamps, the ...

Press Release 

 

DC1287A - LTC6416 Demo Circuit (2 GHz Low Noise Differential 16-Bit ADC Buffer)

Nov 13th 2008
DC1287A - Demo Board for:LTC6416 - 2GHz Low Noise Differential 16-Bit ADC Buffer ...

Demo Board 

 

DC1422A-A - LTC6605-7 | Dual Matched 7MHz Low Noise, Low Distortion 2nd Order LP Filter

Nov 12th 2008
DC1422A-A - Demo Board for:LTC6605-7 - Dual Matched 7MHz Filter with Low Noise, Low Distortion Differential Amplifier ...

Demo Board 

 

DC1422A-B - LTC6605-10 | Dual Matched 10MHz Low Noise, Low Distortion 2nd Order LP Filter

Nov 12th 2008
DC1422A-B - Demo Board for:LTC6605-10 - Dual Matched 10MHz Filter with Low Noise, Low Distortion Differential Amplifier ...

Demo Board 

 

DC1422A-C - LTC6605-14 | Dual Matched 14 MHz Low Noise, Low Distortion 2nd Order LP Filter

Nov 12th 2008
DC1422A-C - Demo Board for:LTC6605-14 - Dual Matched 14MHz Filter with Low Noise, Low Distortion Differential Amplifier ...

Demo Board 

 

DC1251A-A - LTC6601-1 | Low Noise Configurable Broadband Filter Demo Board

Nov 11th 2008
DC1251A-A - Demo Board for:LTC6601-1 - Low Noise, 0.5% Tolerance, 5MHz to 28MHz, Pin Configurable Filter/ADC Driver ...

Demo Board 

 

DC1304A-B - LTC6603 Demo Board | Dual Programmable 2.5MHz Filter / ADC Driver

Sep 23rd 2008
DC1304A-B - Demo Board for:LTC6603 - Dual Adjustable Lowpass Filter ...

Demo Board 

 

Dual 2.5MHz, 5MHz, 10MHz & 15MHz Lowpass Filter with Differential Amplifier & Guaranteed Matching

Sep 9th 2008
MILPITAS, CA - September 9, 2008 - Linear Technology introduces a family of four high performance dual fixed frequency lowpass active filters/amplifiers targeting a wide range of wireless communications and industrial signal processing equipment applications. • LT6604-2.5  2.5MHz Cutoff Frequency • LT6604-5   5MHz ...

Press Release 

 

DC1418A-D - LT6604-15 I Dual Matched 15MHz 4th Order LP Filter Demo Board

Jul 30th 2008
DC1418A-D - Demo Board for:LT6604-15 - Dual Very Low Noise, Differential Amplifier and 15MHz Lowpass Filter ...

Demo Board 

 

DC1418A-C - LT6604-10 Dual Matched 10MHz 4th Order LP Filter Demo Board

Jul 30th 2008
DC1418A-C - Demo Board for:LT6604-10 - Dual Very Low Noise, Differential Amplifier and 10MHz Lowpass Filter ...

Demo Board 

 

DC987B-A - LTC6400-8 3GHz Fully Differential ADC Driver Demo Circuit

Jul 16th 2008
DC987B-A - Demo Board for:LTC6400-8 - 2.2GHz Low Noise, Low Distortion Differential ADC Driver for DC-300MHz ...

Demo Board 

 

DC1418A-B - LT6604-5 | Dual Matched 5MHz 4th Order LP Filter Demo Board

Jul 8th 2008
DC1418A-B - Demo Board for:LT6604-5 - Dual Very Low Noise, Differential Amplifier and 5MHz Lowpass Filter ...

Demo Board 

 

DC1418A-A - LT6604-2.5 | Dual Matched 2.5MHz 4th Order LP Filter Demo Board

Jul 8th 2008
DC1418A-A - Demo Board for:LT6604-2.5 - Dual Very Low Noise, Differential Amplifier and 2.5MHz Lowpass Filter ...

Demo Board 

 

DC1147A-F - LTC6405 demo circuit

Jun 4th 2008
DC1147A-F - Demo Board for:LTC6405 - 2.7GHz, 5V, Low Noise, Rail-to-Rail Input Differential Amplifier/Driver ...

Demo Board 

 

DC987B-B - LTC6400-14 3GHz Fully Differential ADC Driver Demo Circuit

May 22nd 2008
DC987B-B - Demo Board for:LTC6400-14 - 2.4GHz Low Noise, Low Distortion Differential ADC Driver for 300MHz IF ...

Demo Board 

 

1.8/1.3GHz, Low Distortion, Dual ADC Drivers Deliver Guaranteed Matching & Low Noise

May 5th 2008
MILPITAS, CA - May 5, 2008 - Linear Technology announces the LTC6420-20 and LTC6421-20, the industry’s first high-speed dual differential ADC drivers with guaranteed gain matching, and exceptional noise and distortion performance. With guaranteed matched gain of ±0.25dB and matched phase of ±0.1° (typ), the LTC6420-20 reduces ...

Press Release 

 

DC987B-F - LTC6401-14 3GHz Fully Differential ADC Driver Demo Circuit

Apr 30th 2008
DC987B-F - Demo Board for:LTC6401-14 - 2GHz Low Noise, Low Distortion Differential ADC Driver for DC-140MHz ...

Demo Board 

 

DC1299A-A - LTC6420CUD-20 | Dual Matched 1.8GHz Differential Amplifiers/ADC Drivers

Apr 2nd 2008
DC1299A-A - Demo Board for:LTC6420-20 - Dual Matched 1.8GHz Differential Amplifiers/ADC Drivers ...

Demo Board 

 

DC1299A-B - LTC6421CUD-20 | Dual Matched 1.3GHz Differential Amplifiers/ADC Drivers

Mar 25th 2008
DC1299A-B - Demo Board for:LTC6421-20 - Dual Matched 1.3GHz Differential Amplifiers/ADC Drivers ...

Demo Board 

 

DC987B-E - LTC6401-8 3GHz Fully Differential ADC Driver Demo Circuit

Feb 8th 2008
DC987B-E - Demo Board for:LTC6401-8 - 2.2GHz Low Noise, Low Distortion Differential ADC Driver for DC-140MHz ...

Demo Board 

 

DC1147A-E - LTC6403-1 demo circuit

Jan 30th 2008
DC1147A-E - Demo Board for:LTC6403-1 - 200MHz, Low Noise, Low Power Fully Differential Input/Output Amplifier/Driver ...

Demo Board 

 

DC987B-H - LTC6401-26 3GHz Fully Differential ADC Driver Demo Circuit

Jan 14th 2008
DC987B-H - Demo Board for:LTC6401-26 - 1.6GHz Low Noise, Low Distortion Differential ADC Driver for DC-140MHz ...

Demo Board 

 

Too many results please adjust your filters