1. Skip to navigation
  2. Skip to content
  3. Skip to sidebar

Solutions Search - Extended Temperature Plastic (H & MP)

Terasic Innovate FPGA Design Contest

Nov 2nd 2017
Welcome to the Innovate FPGA & SoC Design Contest held by Terasic, Analog Devices & Intel. For the past 14 years, this contest has inspired thousands of aspiring engineers to design, to create, and innovate!    YOU MAY PICK 3 FREE LTC / ADI PLUG-IN BOARDS (EITHER FROM THE ARDUINO OR QUIKEVAL CATEGORIES) BY ...

Circuit 

 

Terasic DE10-Nano Kit

Sep 26th 2017
The Terasic DE10-Nano is a development kit based on an Intel Cyclone V SoC which combines the power of a Cyclone V FPGA with a dual-core ARM Cortex-A9 processor. Analog Devices offers many plug-in boards that let you extend the functionality of the kit. Whether you want to measure real-world phenomena such as toxic gases or ...

Circuit LTpowerPlanner 

 

LTC6258 Low Noise Reference Use LT6656 for a Low Current Starting Reference

Aug 30th 2017
The LT6656 is a 1µA precision series voltage reference. Yet with low power comes low drive current capability and higher noise. The LTC6259 can be used as a buffer that follows a filter to enhance the utilization of the LT6656 in low power applications. Figure 5a shows such a configuration. First a very low cutoff frequency ...

Circuit LTspice 

 

LTC6258 Low Power Squarewave - Sinewave Oscillator

Aug 30th 2017
A low power sine wave generator can be derived by driving a square wave into the bandpass filter. A complete schematic is shown in Figure 4a. The LTC6992-1 easily configures as a 50% duty cycle 10kHz square wave, and can drive the relatively benign loading seen in the bandpass filter. Figures 4b and 4c show the LTC6992-1 output ...

Circuit LTspice 

 

LTC6258 LED Driver with Self-Oscillation

Aug 30th 2017
The circuit above combines edge detection with use of the shutdown pin of the LTC6259. R2 and R3 bring in a divided down copy of the supply voltage as a reference into the positive terminal. The op amp forces this voltage on the sense resistor RSENSE in “LED ON” operation. In that sense this circuit is similar to ...

Circuit LTspice 

 

LTC6258 Lower Power LED Driver with Voltage Command

Aug 30th 2017
Figure above shows a voltage controlled LED drive circuit. When VIN is at 0V, the op amp supply current is nominally 20μA. The offset, for example, could be 450µV, appears across R1, inducing a 0.45mA current in the LED. Some applications want a guaranteed zero LED current at VIN = 0, and this is the purpose of R5. ...

Circuit LTspice 

 

LTC2063 Micropower Precision Oxygen Sensor

Jul 27th 2017
This low power precision gas sensor circuit operates in an oxygen level range of 0% to 30%, with a nominal output of 1V in normal atmospheric oxygen concentrations (20.9%) when the gas sensor has been fully initialized. Total active power consumption is less than 2.1μA on a single rail supply. Since ...

Circuit LTspice 

 

LTC2063 RTD Sensor with ±1°C Precision

Jul 27th 2017
This low power platinum resistance temperature detector (RTD) sensor circuit draws only 35μA total supply current on a minimum 2.6V rail, and is accurate to within ±1°C at room temperature, including all error intrinsic to the Vishay PTS Class F0.3 Variant RTD. It covers the temperature ...

Circuit LTspice 

 

LT1997-3 - Single Supply Current Sense

Jun 14th 2017
Sense resistors R1 converts a current into a voltage. This voltage is buffered (gain of 1) from the input to the output in this amplifier. V1 tests the circuit for response to common mode variation. A simulation will show that the output voltage variation due to the common mode voltage V1 is very small.     The ...

Circuit LTspice 

 

LT1997-3 - Conversion of Single Ended Pulse To Differential Output

Jun 14th 2017
This circuit combines the LT®1997-3 with a high speed amplifier to convert a single-ended signal to differential with a common-mode offset. Extra compensation capacitors C1 and C2 help to shape the final response. Taking higher gain from the LT1997-3 will eliminate the need for these capacitors.     The LT1997-3 ...

Circuit LTspice 

 

LTC6261 Audio Headphones Bridge Driver

May 22nd 2017
The LTC®6261/LTC6262/LTC6263 are single/dual/quad operational amplifiers with low noise, low power, low supply voltage, and rail-to-rail inputs and outputs. They are unity gain stable with capacitive loads up to 1nF. They feature 30MHz gain-bandwidth product, 7V/μs slew rate while consuming only 240μA of supply current ...

Circuit LTspice 

 

LT8310/LT1431 92W Isolated Forward Converter with Opto Feedback; VIN = 48V, VOUT = 54V@1.7A

George Qian - Senior Applications Engineer Mar 29th 2017
The LT8310 is a constant-frequency resonant reset forward converter controller with a low side N-channel MOSFET gate driver. The LT8310 has a wide input voltage range from 6V to 100V. Its switching frequency can be programed from 100kHz to 500kHz to optimize efficiency, performance or external component size. The LT8310’s ...

Blog Post Circuit LTspice 

 

LT4320 LT4320 Ideal Diode Bridge

Jan 27th 2017
The LT®4320/LT4320-1 are ideal diode bridge controllers that drive four N-channel MOSFETs, supporting voltage rectification from DC to 600Hz typical. By maximizing available voltage and reducing power dissipation (see thermograph comparison below), the ideal diode bridge simplifies power supply design and reduces power supply ...

Circuit 

 

LTC3897 High Efficiency 2-Phase 24V Boost Converter with In-Rush Current Control, Overcurrent Protection, Input Voltage Surge Protection and Reverse Input Protection

Jan 17th 2017
The LTC®3897 is a synchronous boost DC/DC controller with surge stopper and ideal diode controller. ...

Circuit 

 

LTC3897 High Efficiency 2-Phase 48V Boost Converter with Reverse Input Protection (Surge Stopper Controller Not Used)

Jan 17th 2017
The LTC®3897 is a synchronous boost DC/DC controller with surge stopper and ideal diode controller. ...

Circuit 

 

LTC3897 High Efficiency 2-Phase 48V Boost Converter with Overcurrent Protection (Ideal Diode and Surge Stopper Controllers at the Output)

Jan 17th 2017
The LTC®3897 is a synchronous boost DC/DC controller with surge stopper and ideal diode controller. ...

Circuit 

 

LTC3897 Nonsynchronous 107V/1.5A 2-Phase Boost Converter with In-Rush Current Control, Overcurrent Protection, Input Voltage Surge Protection and Reverse Input Protection

Jan 17th 2017
The LTC®3897 is a synchronous boost DC/DC controller with surge stopper and ideal diode controller. ...

Circuit 

 

LTC6261 Second Order Bessel Filter

Jan 17th 2017
The LTC®6261/LTC6262/LTC6263 are single/dual/quad operational amplifiers with low noise, low power, low supply voltage, and rail-to-rail inputs and outputs. They are unity gain stable with capacitive loads up to 1nF. They feature 30MHz gain-bandwidth product, 7V/μs slew rate while consuming only 240μA of supply current ...

Circuit LTspice 

 

LTC6261 Third Order Butterworth Filter

Jan 17th 2017
The LTC®6261/LTC6262/LTC6263 are single/dual/quad operational amplifiers with low noise, low power, low supply voltage, and rail-to-rail inputs and outputs. They are unity gain stable with capacitive loads up to 1nF. They feature 30MHz gain-bandwidth product, 7V/μs slew rate while consuming only 240μA of supply current ...

Circuit LTspice 

 

Hybrid Wide Dimming Ratio Linear LED Current Controller Using LT8614 & LT3083/LT6015

Tom Mosteller - Field Applications Engineer Oct 17th 2016
Many applications for LED illumination require wide dimming ratios. This can be accomplished simply via an adjustable current source as show below.  The current source can be varied by a number of different means, and a large LED current range can be achieved. The primary problem with this technique is that the power dissipation ...

Blog Post Circuit LTspice 

 

LT3759 Wide Vin, 48V @ >100mA Output Boost Converter that Works Down to 1.6V

Christopher Jarboe - Associate Applications Engineer Oct 3rd 2016
The LT®3759 is a wide input range, current mode, DC/DC controller which is capable of regulating either positive or negative output voltages from a single feedback pin. It can be configured as a boost, SEPIC or inverting converter. An internal LDO regulator draws power from VIN or DRIVE to provide up to a 4.75V supply for ...

Blog Post Circuit LTspice 

 

Op Amp Precision Positive & Negative Clipper using LT6015/LT6016/LT6017

Tom Mosteller - Field Applications Engineer
Aaron Schultz - Applications Manager Signal Conditioning
Oct 3rd 2016
It can be a challenge to match the voltage range of an analog signal to the input range of an analog to digital converter (ADC). Exceeding the ADC’s input range will give an incorrect reading, and if the input goes far enough beyond the power supply rails substrate currents can flow into the ADC which can cause latch up ...

Blog Post Circuit LTspice 

 

Single-Ended to Differential Driver Circuit for the LTC2387-18 SAR ADC

Doug Stuetzle - Senior Analog Applications Engineer Sep 26th 2016
The LTC®2387-18 is a 15Msps, highly linear, low-noise SAR converter with differential inputs. The combination of excellent linearity and wide dynamic range makes this ADC ideal for high speed imaging and instrumentation applications. No-latency operation provides a unique solution for high speed control loop applications. ...

Blog Post Circuit LTspice 

 

LTC3126 5V, 2MHz Step-Down Converter with Dual Inputs

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LTC3126 12V, 2MHz Step-Down Converter with Dual Inputs

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LTC3126 1.8V, 2MHz Step-Down Converter with Dual Inputs

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LTC3126 3.3V, 2MHz Step-Down Converter with Dual Inputs

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LTC3126 3.3V Supply with 200ms Transient Ride-Through Capability

Sep 16th 2016
The LTC®3126 is a high efficiency synchronous buck converter with an internal no-loss PowerPath™ supporting seamless operation from two separate input power sources. Pin selectable ideal diode-OR and priority input modes with user programmable undervoltage lockout thresholds provide full control over the transition ...

Circuit 

 

LT3090 5V to +/-2.5V Low Noise Power Supply

Sep 15th 2016
The LT®3090 is a 600mA, low dropout negative linear regulator that is easily parallelable to increase output current or spread heat on surface mounted boards. Designed with a precision current reference followed by a high performance rail-to-rail voltage buffer, this regulator finds use in applications requiring precision ...

Circuit 

 

LT3090 Two-Terminal Current Source

Sep 15th 2016
The LT®3090 is a 600mA, low dropout negative linear regulator that is easily parallelable to increase output current or spread heat on surface mounted boards. Designed with a precision current reference followed by a high performance rail-to-rail voltage buffer, this regulator finds use in applications requiring precision ...

Circuit 

 

LT3090 500mA LED Driver with Grounded LED Tab (Heatsink)

Sep 15th 2016
The LT®3090 is a 600mA, low dropout negative linear regulator that is easily parallelable to increase output current or spread heat on surface mounted boards. Designed with a precision current reference followed by a high performance rail-to-rail voltage buffer, this regulator finds use in applications requiring precision ...

Circuit 

 

LT3065 LED Driver/Current Source

Sep 15th 2016
The LT®3065 Series are micropower, low noise, low dropout voltage (LDO) linear regulators that operate over a 1.8V to 45V input voltage range. The devices supply 500mA of output current with a typical dropout voltage of 300mV. A single external capacitor provides programmable low noise reference performance and output soft-start ...

Circuit 

 

LT3085 Low Voltage, High Current Adjustable High Efficiency Regulator

Sep 15th 2016
The LT3085 is a 500mA low dropout linear regulator that can be paralleled to increase output current or spread heat on surface mounted boards. Designed as a precision current source and voltage follower, this new regulator finds use in many applications requiring high current, adjustability to zero, and no heat sink. The device ...

Circuit 

 

LT3085 Low Dropout Voltage LED Driver

Sep 15th 2016
The LT3085 is a 500mA low dropout linear regulator that can be paralleled to increase output current or spread heat on surface mounted boards. Designed as a precision current source and voltage follower, this new regulator finds use in many applications requiring high current, adjustability to zero, and no heat sink. The device ...

Circuit 

 

LT3085 Adjustable High Efficiency Regulator

Sep 15th 2016
The LT3085 is a 500mA low dropout linear regulator that can be paralleled to increase output current or spread heat on surface mounted boards. Designed as a precision current source and voltage follower, this new regulator finds use in many applications requiring high current, adjustability to zero, and no heat sink. The device ...

Circuit 

 

LT3517 Buck Mode 1A LED Driver

Sep 13th 2016
The LT3517 is a current mode DC/DC converter with an internal 1.5A, 45V switch specifically designed to drive LEDs. The LT3517 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3517 350mA, 5V to 12V Boost Converter with Accurate Input Current Limit

Sep 13th 2016
The LT3517 is a current mode DC/DC converter with an internal 1.5A, 45V switch specifically designed to drive LEDs. The LT3517 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3517 Low Side current Sensing Load Dump Protected Buck-Boost Mode LED Driver

Sep 13th 2016
The LT3517 is a current mode DC/DC converter with an internal 1.5A, 45V switch specifically designed to drive LEDs. The LT3517 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3517 Boost 100mA LED Driver with LED Open Protection

Sep 13th 2016
The LT3517 is a current mode DC/DC converter with an internal 1.5A, 45V switch specifically designed to drive LEDs. The LT3517 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3517 5.5V SEPIC Convener with Short-Circuit Protection

Sep 13th 2016
The LT3517 is a current mode DC/DC converter with an internal 1.5A, 45V switch specifically designed to drive LEDs. The LT3517 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3599 12W LED Driver 1MHz Boost, 80mA per String, 10 LEDs per String

Sep 9th 2016
The LT3599 is a fixed frequency 2A step-up DC/DC converter designed to drive four strings of 120mA LEDs up to a 44V output voltage. The switching frequency is programmable from 200kHz to 2.1MHz through an external resistor. ...

Circuit 

 

LT3599 12W LED Driver 400kHz Boost, Two LED Strings, 200mA per String, 8 LEDs per String

Sep 9th 2016
The LT3599 is a fixed frequency 2A step-up DC/DC converter designed to drive four strings of 120mA LEDs up to a 44V output voltage. The switching frequency is programmable from 200kHz to 2.1MHz through an external resistor. ...

Circuit 

 

LT3599 7W LED Driver SEPIC (Survives Output Short to Ground) 300kHz, Three Strings, 100mA per String, 6 LEDs per String

Sep 9th 2016
The LT3599 is a fixed frequency 2A step-up DC/DC converter designed to drive four strings of 120mA LEDs up to a 44V output voltage. The switching frequency is programmable from 200kHz to 2.1MHz through an external resistor. ...

Circuit 

 

LT3599 8W LED Driver 2MHz Boost, Three Strings, 100mA per String, 7 LEDs per String

Sep 9th 2016
The LT3599 is a fixed frequency 2A step-up DC/DC converter designed to drive four strings of 120mA LEDs up to a 44V output voltage. The switching frequency is programmable from 200kHz to 2.1MHz through an external resistor. ...

Circuit 

 

LT3599 2.1 MHz Boost, Four Strings, 80mA per String, 7 LEDs per String

Sep 9th 2016
The LT3599 is a fixed frequency 2A step-up DC/DC converter designed to drive four strings of 120mA LEDs up to a 44V output voltage. The switching frequency is programmable from 200kHz to 2.1MHz through an external resistor. ...

Circuit 

 

LTC3112 5V Backup Supply from Supercap Runs Down to VIN = 2V with 250mA Load

Sep 9th 2016
The LTC®3112 is a fixed frequency synchronous buck-boost DC/DC converter with an extended input and output range. The unique 4-switch, single inductor architecture provides low noise and seamless operation from input voltages above, below or equal to the output voltage. ...

Circuit 

 

LTC3112 Regulated 12V Output from Wide Input Supply Range

Sep 9th 2016
The LTC®3112 is a fixed frequency synchronous buck-boost DC/DC converter with an extended input and output range. The unique 4-switch, single inductor architecture provides low noise and seamless operation from input voltages above, below or equal to the output voltage. ...

Circuit 

 

LTC3112 10W, 10V High Intensity LED Driver with Programmable Current and Low-Loss Sensing

Sep 9th 2016
The LTC®3112 is a fixed frequency synchronous buck-boost DC/DC converter with an extended input and output range. The unique 4-switch, single inductor architecture provides low noise and seamless operation from input voltages above, below or equal to the output voltage. ...

Circuit 

 

LTC3114-1 Constant Current High Brightness LED Driver

Sep 9th 2016
The LTC®3114-1 is a versatile, wide operating voltage range synchronous monolithic buck-boost DC/DC converter with programmable average output current. The LTC3114-1’s proprietary buck-boost PWM control circuitry delivers low noise operation across the entire operating voltage range. Current mode control ensures exceptional ...

Circuit 

 

LT3795 Short-Circuit Robust Boost LED Driver with Input Current Limit and Spread Spectrum Frequency Modulation

Sep 8th 2016
The LT®3795 is a DC/DC controller designed to regulate a constant-current or constant-voltage and is ideal for driving LEDs. It drives a low side external N-channel power MOSFET from an internal regulated 7.7V supply. The fixed frequency and current mode architecture result in stable operation over a wide range of supply ...

Circuit 

 

LT3795 SEPIC LED Driver with Input Current Limit

Sep 8th 2016
The LT®3795 is a DC/DC controller designed to regulate a constant-current or constant-voltage and is ideal for driving LEDs. It drives a low side external N-channel power MOSFET from an internal regulated 7.7V supply. The fixed frequency and current mode architecture result in stable operation over a wide range of supply ...

Circuit 

 

LT3795 Buck Mode LED Driver

Sep 8th 2016
The LT®3795 is a DC/DC controller designed to regulate a constant-current or constant-voltage and is ideal for driving LEDs. It drives a low side external N-channel power MOSFET from an internal regulated 7.7V supply. The fixed frequency and current mode architecture result in stable operation over a wide range of supply ...

Circuit 

 

LT3795 Buck Mode LED Driver with 3000:1 PWM Dimming

Sep 8th 2016
The LT®3795 is a DC/DC controller designed to regulate a constant-current or constant-voltage and is ideal for driving LEDs. It drives a low side external N-channel power MOSFET from an internal regulated 7.7V supply. The fixed frequency and current mode architecture result in stable operation over a wide range of supply ...

Circuit 

 

LT3518 Buck Mode 1.5A LED Driver

Sep 8th 2016
The LT3518 is a current mode DC/DC converter with an internal 2.3A, 45V switch specifically designed to drive LEDs. The LT3518 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3518 Buck-Boost Mode LED Driver

Sep 8th 2016
The LT3518 is a current mode DC/DC converter with an internal 2.3A, 45V switch specifically designed to drive LEDs. The LT3518 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3518 Buck Mode 1A LED Driver with Open LED Protection and Sync Input

Sep 8th 2016
The LT3518 is a current mode DC/DC converter with an internal 2.3A, 45V switch specifically designed to drive LEDs. The LT3518 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LT3518 Boost 300mA LED Driver with LED Open Protection

Sep 8th 2016
The LT3518 is a current mode DC/DC converter with an internal 2.3A, 45V switch specifically designed to drive LEDs. The LT3518 operates as a LED driver in boost, buck mode and buck-boost mode. It combines a traditional voltage loop and a unique current loop to operate as a constant-current source or constant-voltage source. ...

Circuit 

 

LTM4643 4V to 20V Input, Quad 1.2V, 1.5V, 2.5V and 3.3V Output with Ratiometric Tracking

Sep 8th 2016
The LTM®4643 is a quad DC/DC step-down μModule (power module) regulator with 3A per output. Outputs can be paralleled in an array for up to 12A capability. Included in the package are the switching controllers, power FETs, inductors and support components. Operating over an input voltage range of 4V to 20V or 2.375V to ...

Circuit 

 

LTM4643 2.375V to 5V Input, Quad 1V, 1.2V, 1.5V, 1.8V Output

Sep 8th 2016
The LTM®4643 is a quad DC/DC step-down μModule (power module) regulator with 3A per output. Outputs can be paralleled in an array for up to 12A capability. Included in the package are the switching controllers, power FETs, inductors and support components. Operating over an input voltage range of 4V to 20V or 2.375V to ...

Circuit 

 

LTM4643 4V to 20V Input, 4-Phase, 1.2V at 12A Design with Temperature Monitoring

Sep 8th 2016
The LTM®4643 is a quad DC/DC step-down μModule (power module) regulator with 3A per output. Outputs can be paralleled in an array for up to 12A capability. Included in the package are the switching controllers, power FETs, inductors and support components. Operating over an input voltage range of 4V to 20V or 2.375V to ...

Circuit 

 

LTM4643 12V and 5V Two Separate Input Rails, 1.2V at 6A and 3.3V at 6A Output

Sep 8th 2016
The LTM®4643 is a quad DC/DC step-down μModule (power module) regulator with 3A per output. Outputs can be paralleled in an array for up to 12A capability. Included in the package are the switching controllers, power FETs, inductors and support components. Operating over an input voltage range of 4V to 20V or 2.375V to ...

Circuit 

 

LT3755 20W SEPIC LED Driver

Sep 6th 2016
The LT3755, LT3755-1 and LT3755-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3755 Buck Mode 1.4A LED Driver

Sep 6th 2016
The LT3755, LT3755-1 and LT3755-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3755 Buck Mode 500mA LED Driver for 20kHz PWM Dimming

Sep 6th 2016
The LT3755, LT3755-1 and LT3755-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3755 21W Buck-Boost Mode with 250:1 PWM Dimming and Open LED Protection

Sep 6th 2016
The LT3755, LT3755-1 and LT3755-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3755 Buck-Boost LED Driver for Automotive

Sep 6th 2016
The LT3755, LT3755-1 and LT3755-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3756 30W White LED Headlamp Driver with Thermal Derating

Sep 6th 2016
The LT3756, LT3756-1 and LT3756-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current-mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3756 Buck-Boost Mode LED Driver

Sep 6th 2016
The LT3756, LT3756-1 and LT3756-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current-mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3756 90% Efficient, 20W SEPIC LED Driver

Sep 6th 2016
The LT3756, LT3756-1 and LT3756-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current-mode architecture results in stable operation over a wide range of ...

Circuit 

 

LT3756 Buck Mode 1A LED Driver with High Dimming Ratio and Open LED Reporting

Sep 6th 2016
The LT3756, LT3756-1 and LT3756-2 are DC/DC controllers designed to operate as a constant-current source for driving high current LEDs. They drive a low side external N-channel power MOSFET from an internal regulated 7.15V supply. The fixed frequency, current-mode architecture results in stable operation over a wide range of ...

Circuit 

 

LTC3245 High Efficiency 3.3V Microcontroller Supply from 9V Alkaline (with Power-On Reset Delay)

Sep 2nd 2016
The LTC3245 is a switched capacitor buck-boost DC/DC converter that produces a regulated output (3.3V, 5V or adjustable) from a 2.7V to 38V input. The device uses switched capacitor fractional conversion to maintain regulation over a wide range of input voltage. Internal circuitry automatically selects the conversion ratio to ...

Circuit 

 

LTC3245 Wide Input Range Low Noise 3.6V Supply

Sep 2nd 2016
The LTC3245 is a switched capacitor buck-boost DC/DC converter that produces a regulated output (3.3V, 5V or adjustable) from a 2.7V to 38V input. The device uses switched capacitor fractional conversion to maintain regulation over a wide range of input voltage. Internal circuitry automatically selects the conversion ratio to ...

Circuit 

 

LTC3245 Wide VIN 5V Supply with Battery Backup

Sep 2nd 2016
The LTC3245 is a switched capacitor buck-boost DC/DC converter that produces a regulated output (3.3V, 5V or adjustable) from a 2.7V to 38V input. The device uses switched capacitor fractional conversion to maintain regulation over a wide range of input voltage. Internal circuitry automatically selects the conversion ratio to ...

Circuit 

 

LTC3261 15V to –15V Inverter

Sep 2nd 2016
The LTC®3261 is a high voltage inverting charge pump that operates over a wide 4.5V to 32V input range and is capable of delivering up to 100mA of output current. ...

Circuit 

 

LTC3261 24V to –24V 100mA Inverter

Sep 2nd 2016
The LTC®3261 is a high voltage inverting charge pump that operates over a wide 4.5V to 32V input range and is capable of delivering up to 100mA of output current. ...

Circuit 

 

LT3965 Matrix LED Dimmer Powered by a Boost-Buck LED Driver

Sep 2nd 2016
The LT®3965 is an LED bypass switching device for dimming individual LEDs in a string using a common current source. It features eight individually controlled floating source 17V/330mΩ NMOS switches. The eight switches can be connected in parallel and/or in series to bypass current around one or more LEDs in a string. ...

Circuit 

 

LT8391 93% Efficient 84W Buck-Boost LED Driver from 24VAC

Sep 2nd 2016
The LT®8391 is a synchronous 4-switch buck-boost LED controller that regulates LED current from input voltage above, below, or equal to the output voltage. The proprietary peak-buck peak-boost current mode control scheme allows adjustable and synchronizable 150kHz to 650kHz fixed frequency operation, or internal ±15% ...

Circuit 

 

LT3763 20A, Pulse Width Modulated, Single LED Driver

Sep 2nd 2016
The LT3763 is a fixed frequency, synchronous, step-down DC/DC controller designed to accurately regulate output currents up to 20A. The average current mode control- ler will maintain inductor current regulation over a wide output voltage range from 0V to 55V. Output current is set by analog voltages on the CTRL pins and an ...

Circuit 

 

LT3763 1A, Five LED Driver

Sep 2nd 2016
The LT3763 is a fixed frequency, synchronous, step-down DC/DC controller designed to accurately regulate output currents up to 20A. The average current mode control- ler will maintain inductor current regulation over a wide output voltage range from 0V to 55V. Output current is set by analog voltages on the CTRL pins and an ...

Circuit 

 

LT3763 350W White LED Driver

Sep 2nd 2016
The LT3763 is a fixed frequency, synchronous, step-down DC/DC controller designed to accurately regulate output currents up to 20A. The average current mode control- ler will maintain inductor current regulation over a wide output voltage range from 0V to 55V. Output current is set by analog voltages on the CTRL pins and an ...

Circuit 

 

Too many results please adjust your filters