1. Skip to navigation
  2. Skip to content
  3. Skip to sidebar

Solutions Search - Extended Temperature (H & MP) System Montior

LTC6363 Differential AV = 1/9 Configuration Using an LT®5400 Quad-Matched Resistor Network

Aug 31st 2015
The LTC®6363 is a low power, low noise, fully differential op amp with rail-to-rail outputs optimized to drive low power SAR ADCs. The LTC6363 draws only 1.9mA supply current in active operation and features a shutdown mode which reduces the current consumption to 20μA (VS = 3V). ...

Circuit 

 

LTC4226 Parallel MOSFETs in Hot Swap Circuits

Dan Eddleman - Senior Applications Engineer
Gabino Alonso - Strategic Marketing Engineer
Mar 13th 2015
The Good, the Bad, and the Ugly Introduction While it is often desirable, and sometimes absolutely critical, to use multiple parallel MOSFETs in Hot Swap™ circuits, careful analysis of Safe Operating Area (SOA) is essential. Each additional parallel MOSFET added to a circuit improves the voltage drop, power loss, and ...

Blog Post Circuit LTspice 

 

LTM4639 2.375V to 7VIN, 1.5V at 20A uModule Design

Nov 24th 2014
The LTM®4639 is a complete 20A output high efficiency switch mode step-down DC/DC μModule (micromodule) regulator. Included in the package are the switching controller, power FETs, inductor and compensation components. Operating over an input voltage range from 2.375V to 7V, the LTM4639 supports an output voltage range ...

Circuit 

 

Altera Audio Video Development Kit, Stratix IV GX Edition

Jun 12th 2014
The Audio Video Development Kit, Stratix IV GX Edition, delivers a complete video and image processing development environment for design engineers. The kit facilitates the entire design process, from design conception through hardware implementation. This kit includes the Stratix IV EP4SGX230 FPGA development ...

Circuit 

 

Altera Stratix IV GX FPGA Development Kit

Jun 12th 2014
The Altera Stratix IV GX FPGA Development Kit delivers a complete system-level design environment that includes both the hardware and software needed to immediately begin developing FPGA designs. With this PCI-SIG-compliant board and a one-year license for Quartus II design software, you can develop and test PCI Express ...

Circuit 

 

Altera Stratix V GX FPGA Development Kit

Jun 11th 2014
The Altera® Stratix® V GX FPGA Development Kit provides a complete design environment that includes all the hardware and software you need to begin developing FPGA designs immediately. The development kit is RoHS compliant. You can use this development kit to do the following: Develop and test PCI Express® (PCIe®) designs ...

Circuit 

 

Altera Stratix IV E FPGA Development Kit

Jun 5th 2014
The Altera Stratix IV E FPGA Development Kit delivers a complete system-level design environment that includes both the hardware and software needed to immediately begin developing FPGA designs. You can use this development kit to develop and test memory subsystems consisting of DDR3 DIMMs, QDR II+, and RLDRAM ...

Circuit 

 

LTC2960 Battery Disconnect to Protect Against Deep Discharge

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout period ...

Circuit 

 

LTC2960 Micropower Power Supply Sequencer and Supervisor

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout period ...

Circuit 

 

LTC2960 Automotive Supervisor

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout period ...

Circuit 

 

LTC2960 Li-Ion Battery and Regulator Monitor

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout period ...

Circuit 

 

LTC2960 Window Comparator for High Voltage Input

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout period ...

Circuit