Solutions Search - Differential Amplifiers
DC2473A - LTC6419 - Dual Differential Amplifiers / ADC Drivers
Mar 15th 2017
Demonstration circuit 2473A features the LTC®6419 Dual Differential Amplifier/ADC Driver. It incorporates a variety of passive components to support configurations for varied applications. These fully-differential amplifiers accept single-ended or differential input with almost no difference in distortion performance.
...
Improving Linearity by Using Absorptive Filters
Mar 10th 2017
Introduction:
When driving a direct sampling high speed ADC, the most likely place to degrade the performance is the interface between the final amplifier and the ADC. With any direct sampling ADC there will be nonlinear charge produced in the sampling process. This charge is reflected into the input network each time the sampling ...
High Linearity, Low Noise LTC2387-18 Drivers for Sinusoidal Signals
Jan 10th 2017
Introduction
The LTC2387-18 is a high speed SAR (Successive Approximation Register) ADC suited for high linearity, low noise applications. This ADC is capable of sampling at up to 15Msps, which allows it to convert signals at frequencies of several MHz. It is well-suited to convert both pulsed and continuous signals in this ...
DC2487A - LTC6363 Rail-to-Rail SAR ADC Driver Amplifier
Jan 10th 2017
Demonstration circuit 2487A features the LTC®6363 amplifier. The DC2487A is designed to drive the inputs of the DC2290A demo board. The DC2290A features the LTC®2387 18-bit, 15Msps high speed SAR ADC. The linearity and low noise of the LTC6363 make it an ideal candidate to drive the LTC2387 at frequencies up to 100kHz.
...
LTC2387 Drivers Part III: Trans-Impedance Amplifier/Driver
Sep 8th 2016
This is unabashedly a classic case of what marketing calls “a solution looking for a problem”. It is an example of how the full SNR of the LTC2387 may be realized for a real world signal. Most signals originating in low level circuitry, in sensors, or in the real world, will require significant gain to develop 8Vp-p ...
Anti-Alias Filter for 24-bit ADC
Aug 3rd 2016
For many ADC applications a simple RC filter at the buffer input will provide adequate anti-alias filtering. For applications that require a higher order filter an active filter is often used. The active component in that filter must have sufficient bandwidth, fast settling, low noise and low offset so that it doesn’t ...
Baseband Design Example for LTC5589/LTC5599 Low-Power IQ Modulator
Jul 1st 2016
Introduction
This basic low power modulator was described in the LT Journal Nov 2015 article. In this blog post, we will show how to:
Use simulation to validate the filter design, and
Reduce DC offsets by utilizing Differential Amplifiers for the baseband drive.
Also shown are some miscellaneous tips to help complete ...
How to Drive the LTC2387 (Part 1): Signal Applications to 5MHz that Require Low Inter-Modulation Distortion
May 13th 2016
The biggest challenge in driving a 15Msps, 18-bit ADC with an 8Vp-p input range is the lack of integrated amplifiers with adequate bandwidth, low noise, and the required output excursion. There are low-noise, high-BW amplifiers than can produce 2VPP. There are low speed amplifiers than can produce 8VPP. For low distortion beyond ...
DC2319A-A - LTC6363 Differential Op Amp/ADC Driver Demo Board
Nov 10th 2015
The LTC®6363 is a low power, low noise differential op amp with rail-to-rail output swing and good DC accuracy. The amplifier may be configured to process a fully differential input signal or to convert a single-ended input signal to a differential output signal. The differential outputs of the DC2319A can be configured ...
Precision Differential Amplifier Drives 20-Bit ADCs Consuming Less than 2mA
Sep 24th 2015
MILPITAS, CA - September 24, 2015 - Linear Technology introduces
the LTC6363, a low
power, high precision, fully differential amplifier optimized for
driving high performance 16-, 18- and 20-bit SAR and ΔΣ ADCs.
Featuring 100µV maximum input offset voltage and 2.9nV/√Hz
input-referred voltage noise, the LTC6363 consumes ...
Driving High Resolution SAR ADCs
Sep 8th 2015
Driving high resolution SAR ADCs often requires tradeoffs between power consumption, linearity, and noise. The LTC6363 provides 20 bit accuracy when the system designer pays close attention to the interface filter between the driver and the ADC. Calculations and empirical data provide additional insight as to how ...
LTC6363 LTC6363 Used as Lowpass Filter/Driver with 10VP-P Singled-Ended Input, Driving a SAR ADC
Aug 31st 2015
The LTC®6363 is a low power, low noise, fully differential op amp with rail-to-rail outputs optimized to drive low power SAR ADCs. The LTC6363 draws only 1.9mA supply current in active operation and features a shutdown mode which reduces the current consumption to 20μA (VS = 3V). ...
LTC6363 Differential AV = 1/9 Configuration Using an LT®5400 Quad-Matched Resistor Network
Aug 31st 2015
The LTC®6363 is a low power, low noise, fully differential op amp with rail-to-rail outputs optimized to drive low power SAR ADCs. The LTC6363 draws only 1.9mA supply current in active operation and features a shutdown mode which reduces the current consumption to 20μA (VS = 3V). ...
LTC6363 Single-Ended-to-Differential Conversion of a 20VP-P Ground-Referenced Input with Gain of AV = 0.5 to Drive an ADC
Aug 31st 2015
The LTC®6363 is a low power, low noise, fully differential op amp with rail-to-rail outputs optimized to drive low power SAR ADCs. The LTC6363 draws only 1.9mA supply current in active operation and features a shutdown mode which reduces the current consumption to 20μA (VS = 3V). ...
DC2266A - LTC2107 + LTC6409 Demo Board | 16-Bit, 210Msps ADC and Driver Combo Board, DC-100MHz Input, DDR LVDS Outputs, (req DC1371 and DC2219)
May 20th 2015
Demonstration circuit 2266A features the LTC®2107, 210Msps ADC, and the LTC6409 low noise amplifier. DC2266A supports the LTC2107 DDR LVDS output mode.
The circuitry on the analog inputs is optimized for analog input frequencies from DC to 100MHz. When driven with a 50Ω source, the gain will be 6dB. To modify the ...
LTspice: SAR ADC Driver Interface
Apr 3rd 2014
High-performance SAR ADCs can offer amazing dynamic range and linearity at faster and faster sample rates. But how do you design the amplifier and interface at the analog inputs? LTspice IV can help. This video shows how to use LTspice to simulate the analog input interface of high-performance SAR ADCs. We will look ...
Digital Gain Compression (DGC) for SAR ADCs
Mar 11th 2014
The LTC2378-20 offers a digital gain compression (DGC) feature which defines the full-scale input swing to be between 10% and 90% of the ±VREF analog input range. This feature allows the SAR ADC driver to be powered off of a single positive supply since each input swings between 0.5V and 4.5V as shown in the figure below.
Needing ...
Single-Ended to Differential Conversion Using Differential Op Amps
Jan 13th 2014
Differential op amps are important building blocks in modern analog and mixed signal circuits. Many modern ADCs require differential signals at the inputs. Differential analog signals are also handy to drive signals over a cable. Differential op amps are useful building blocks for creating differential signals. Linear Technology ...
DC1945A - LTC2185 and LTC6409 Combo Board with differential inputs, req DC890, LVDS_XFMR and DC1075
Jan 16th 2013
DC1945A - Demo Board for:LTC2185 - 16-Bit, 125Msps Low Power Dual ADCsLTC6409 - 10GHz GBW, 1.1nV/√Hz Differential Amplifier/ADC Driver
...
Low Noise (1.5nV/√Hz) Fully Differential 1.6GHz Buffer Drives 50Ohm Load
Aug 15th 2012
MILPITAS, CA – August 15, 2012 – Linear Technology announces the
LTC6417, a fully
differential buffer amplifier with only 1.5nV/√Hz output-referred
noise. The LTC6417 is capable of driving a differential 50Ohm load
and is optimized for driving 14- and 16-bit pipeline ADCs. It can
be DC- or AC-coupled at its inputs, and ...
DC1805A-H - LTC6362 with 250ksps 18-bit LTC2376-18 SAR ADC, LTC6655-5. Req DC718 or DC2026
Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal.
...
DC1805A-G - LTC6362 with 500ksps 18-bit LTC2377-18 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026
Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal.
...
DC1805A-F - LTC6362 with 1Msps 18-bit LTC2378-18 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026
Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal.
...
DC1805A-E - LTC6362 with 1.6Msps 18-bit LTC2379-18 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026
Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal.
...
DC1805A-D - LTC6362 with 250ksps 16-bit LTC2376-16 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026
Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal.
...
DC1805A-C - LTC6362 with 500ksps 16-bit LTC2377-16 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026
Jun 6th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal.
...
DC1660B - LTC6417 Demo Circuit 1.6GHz differential ADC buffer, drives 50 Ohm load
May 30th 2012
DC1660B - Demo Board for:LTC6417 - 1.6GHz Low Noise High Linearity Differential Buffer/16-Bit ADC Driver with Fast Clamp
...
DC1805A-B - LTC6362 with 1Msps 16-bit LTC2378-16 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026
May 17th 2012
The LTC®6362 is a low power, low noise differential op amp with rail-to-rail input and output swing that has been optimized to drive low power SAR ADCs. The amplifier may be configured to buffer a fully differential input signal or convert a single-ended input signal to a differential output signal.
...
DC1805A-A - LTC6362 with 2Msps 16-bit LTC2380-16 Demo Board | SAR ADC, LTC6655-5. Req DC718 or DC2026
May 16th 2012
DC1805A-A - Demo Board for:LTC2380-16 - 16-Bit, 2Msps, Low Power SAR ADC with 96dB SNRLTC6362 - Precision, Low Power Rail-to-Rail Input/Output Differential Op Amp/SAR ADC DriverLTC6655 - 0.25ppm Noise, Low Drift Precision References
...
DC1833A - LTC6362 | Precision Low Power Differential ADC Driver Demo Board
May 14th 2012
DC1833A - Demo Board for:LTC6362 - Precision, Low Power Rail-to-Rail Input/Output Differential Op Amp/SAR ADC Driver
...
Fully Differential Amplifier Drives 18-bit ADCs & Consumes only 5mW
May 2nd 2012
MILPITAS, CA – May 2, 2012 – Linear Technology announces the
LTC6362, a low power
fully differential amplifier that can drive high precision 16- and
18-bit SAR ADCs at only 1mA supply current. With 200µV max input
offset voltage and 3.9nV/√Hz input-referred noise, it is well
suited for precision industrial and data acquisition
applications.
The ...
Matched Resistor Networks for Precision Amplifier Applications
May 1st 2012
Introduction
Some ideal op amp configurations assume that the feedback resistors exhibit perfect matching. In practice, resistor non-idealities can affect various circuit parameters such as common mode rejection ratio (CMRR), harmonic distortion and stability. For instance, as shown in Figure 1, a single-ended amplifier configured ...
DC1783A-H - LTC2376-18 with LTC6655-5/LT6350 Demo Board | 18-Bit, 250ksps, SAR ADC with 102dB SNR. Req DC718 or DC2026
Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...
DC1783A-G - LTC2377-18 with LTC6655-5/LT6350 Demo Board | 18-Bit, 500ksps, SAR ADC with 102dB SNR. Req DC718 or DC2026
Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...
DC1783A-F - LTC2378-18 with LTC6655-5/LT6350 Demo Board | 18-Bit, 1Msps, SAR ADC with 102dB SNR. Req DC718 or DC2026
Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...
DC1783A-D - LTC2376-16 with LTC6655-5/LT6350 Demo Board | 16-Bit, 250ksps, SAR ADC with 97dB SNR. Req DC718 or DC2026
Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...
DC1783A-C - LTC2377-16 with LTC6655-5/LT6350 Demo Board | 16-Bit, 500ksps, SAR ADC with 97dB SNR. Req DC718 or DC2026
Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...
DC1783A-B - LTC2378-16 with LTC6655-5/LT6350 Demo Board | 16-Bit, 1Msps, SAR ADC with 97dB SNR. Req DC718 or DC2026
Nov 17th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...
DC1760A - LTC2261-14 + LTC6409 ADC and Driver Combo Board,DC-100MHz, CMOS Outputs, req DC890 and DC1075
Jun 8th 2011
DC1760A - Demo Board for:LTC2261-14 - 14-Bit, 125Msps Ultra-Low Power 1.8V ADCsLTC6409 - 10GHz GBW, 1.1nV/√Hz Differential Amplifier/ADC Driver
...
DC1783A-A - LTC2380-16 with LTC6655-5/LT6350 Demo Board | 16-Bit, 2Msps, SAR ADC with 96dB SNR. Req DC718 or DC2026A
Mar 23rd 2011
DC1783A-A - Demo Board for:LTC2380-16 - 16-Bit, 2Msps, Low Power SAR ADC with 96dB SNRLTC6655 - 0.25ppm Noise, Low Drift Precision ReferencesLT6350 - Low Noise Single-Ended to Differential Converter/ADC Driver
...
DC1783A-E - LTC2379-18 with LTC6655-5/LT6350 Demo Board | 18-Bit, 1.6Msps, SAR ADC with 101dB SNR. Req DC718 or DC2026
Mar 4th 2011
The LTC2380/LTC2379/LTC2378/LTC2377/LTC2376 are low power, low noise ADCs with serial outputs that can operate from a single 2.5V supply. The following text refers to the LTC2379-18 but applies to all parts in the family, the only difference being the maximum sample rates and the number of bits. The LTC2379-18 supports a ±5V ...
DC1600A - LTC6412, LTC2261-14 | 10MHz to 800MHz, 31dB Range Analog Controlled VGA
Nov 15th 2010
DC1600A - Demo Board for:LTC6412 - 800MHz, 31dB Range Analog-Controlled VGA
...
DC1591A - LTC6409 | 10GHz, 1nV/rt(Hz) Differential Amplifier/ADC Driver
Oct 27th 2010
DC1591A - Demo Board for:LTC6409 - 10GHz GBW, 1.1nV/√Hz Differential Amplifier/ADC Driver
...
Differential Amplifier Drives DC-Coupled, Ground-Referenced 100MHz Signals with Low Noise & Low Distortion
Oct 12th 2010
MILPITAS, CA - October 12, 2010 - Linear Technology introduces
the LTC6409, a fully differential amplifier
capable of driving DC to 100MHz signals with just 1.1nV/√Hz noise
and -88dBc HD2/HD3 distortion. Built on an advanced
SiGe BiCMOS process, the LTC6409 features 10GHz gain-bandwidth
product, 100dB SFDR up to 40MHz, and ...
DC1538A - LT6350 demo board
Feb 22nd 2010
DC1538A - Demo Board for:LT6350 - Low Noise Single-Ended to Differential Converter/ADC Driver
...
DC1500A-C - LTC2391-16 with LT6350 optimized driver, 5V 16-bit 250ksps Int Ref Parallel / Serial SAR ADC in LQFP-48, req DC718
Feb 22nd 2010
DC1500A-C - Demo Board for:LT6350 - Low Noise Single-Ended to Differential Converter/ADC DriverLTC2391-16 - 16-Bit, 250ksps SAR ADC with 94dB SNR
...
DC1500A-B - LTC2392-16 with LT6350 optimized driver, 5V 16-bit 500ksps Int Ref Parallel / Serial SAR ADC in LQFP-48, req DC718
Feb 22nd 2010
DC1500A-B - Demo Board for:LTC2392-16 - 16-Bit, 500ksps SAR ADC with 94dB SNRLT6350 - Low Noise Single-Ended to Differential Converter/ADC Driver
...
DC1500A-A - LTC2393-16 with LT6350 optimized driver, 5V 16-bit 1Msps Int Ref Parallel / Serial SAR ADC in LQFP-48, req DC718
Feb 22nd 2010
DC1500A-A - Demo Board for:LTC2393-16 - 16-Bit, 1Msps SAR ADC With 94dB SNR
...
Rail-to-Rail Single-Ended to Differential Amplifier Drives High Speed 16- to 18-bit SAR ADCs
Jan 25th 2010
MILPITAS, CA - January 25, 2010 - Linear Technology introduces
the LT6350, a 33MHz, low
noise, rail-to-rail input and output ADC driver that settles to
16-bits in just 350ns. It is suitable for driving the latest
highest performance SAR ADCs such as the LTC2393-16. The LT6350
incorporates two op amps and matched resistors to ...
DC1257B - LTC6416 + LTC2208 Combo board (Requires DC890 & LVDS_XFMR)
Oct 21st 2009
DC1257B - Demo Board for:LTC6416 - 2GHz Low Noise Differential 16-Bit ADC Buffer
...
800MHz VGA with 31dB Analog Control Range Has 35dBm OIP3 from 3.3V Supply
Jul 14th 2009
MILPITAS, CA - July 14, 2009 - Linear Technology introduces the
LTC6412, an 800MHz
analog-controlled variable gain amplifier (VGA) with outstanding
noise and distortion performance, gain conformance, and gain
flatness. The devices gain control is highly linear. With a
guaranteed maximum conformance error of only 0.45dB, the ...
DC1464A - LTC6412 l 800 MHz, 31dB Range Analog-Controlled VGA
May 26th 2009
DC1464A - Demo Board for:LTC6412 - 800MHz, 31dB Range Analog-Controlled VGA
...
DC1251A-B - LTC6601-2 | Low Power, Low Distortion Configurable Broadband Filter Demo Board
Apr 1st 2009
DC1251A-B - Demo Board for:LTC6601-2 - Low Power, Low Distortion, Low Power, Low Distortion, 5MHz to 27MHz, Pin Configurable Filter/ADC Driver
...
Differential ADC Buffer Drives 300MHz Signals with Only 1.8nV/√Hz Noise
Mar 5th 2009
MILPITAS, CA - March 5, 2009 - Linear Technology introduces the
LTC6416, a wideband unity
gain 2GHz differential buffer aimed at addressing the challenge of
driving high resolution ADCs. The LTC6416 provides excellent noise figure and distortion
performance at high frequencies. With its programmable output
voltage clamps, the ...
DC1287A - LTC6416 Demo Circuit (2 GHz Low Noise Differential 16-Bit ADC Buffer)
Nov 13th 2008
DC1287A - Demo Board for:LTC6416 - 2GHz Low Noise Differential 16-Bit ADC Buffer
...
DC1422A-A - LTC6605-7 | Dual Matched 7MHz Low Noise, Low Distortion 2nd Order LP Filter
Nov 12th 2008
DC1422A-A - Demo Board for:LTC6605-7 - Dual Matched 7MHz Filter with Low Noise, Low Distortion Differential Amplifier
...
DC1422A-B - LTC6605-10 | Dual Matched 10MHz Low Noise, Low Distortion 2nd Order LP Filter
Nov 12th 2008
DC1422A-B - Demo Board for:LTC6605-10 - Dual Matched 10MHz Filter with Low Noise, Low Distortion Differential Amplifier
...
DC1422A-C - LTC6605-14 | Dual Matched 14 MHz Low Noise, Low Distortion 2nd Order LP Filter
Nov 12th 2008
DC1422A-C - Demo Board for:LTC6605-14 - Dual Matched 14MHz Filter with Low Noise, Low Distortion Differential Amplifier
...
DC1251A-A - LTC6601-1 | Low Noise Configurable Broadband Filter Demo Board
Nov 11th 2008
DC1251A-A - Demo Board for:LTC6601-1 - Low Noise, 0.5% Tolerance, 5MHz to 28MHz, Pin Configurable Filter/ADC Driver
...
DC1304A-B - LTC6603 Demo Board | Dual Programmable 2.5MHz Filter / ADC Driver
Sep 23rd 2008
DC1304A-B - Demo Board for:LTC6603 - Dual Adjustable Lowpass Filter
...
Dual 2.5MHz, 5MHz, 10MHz & 15MHz Lowpass Filter with Differential Amplifier & Guaranteed Matching
Sep 9th 2008
MILPITAS, CA - September 9, 2008 - Linear Technology introduces
a family of four high performance dual fixed frequency lowpass
active filters/amplifiers targeting a wide range of wireless
communications and industrial signal processing equipment
applications.
• LT6604-2.5
2.5MHz Cutoff Frequency
• LT6604-5
5MHz ...
DC1418A-D - LT6604-15 I Dual Matched 15MHz 4th Order LP Filter Demo Board
Jul 30th 2008
DC1418A-D - Demo Board for:LT6604-15 - Dual Very Low Noise, Differential Amplifier and 15MHz Lowpass Filter
...
DC1418A-C - LT6604-10 Dual Matched 10MHz 4th Order LP Filter Demo Board
Jul 30th 2008
DC1418A-C - Demo Board for:LT6604-10 - Dual Very Low Noise, Differential Amplifier and 10MHz Lowpass Filter
...
DC987B-A - LTC6400-8 3GHz Fully Differential ADC Driver Demo Circuit
Jul 16th 2008
DC987B-A - Demo Board for:LTC6400-8 - 2.2GHz Low Noise, Low Distortion Differential ADC Driver for DC-300MHz
...
DC1418A-B - LT6604-5 | Dual Matched 5MHz 4th Order LP Filter Demo Board
Jul 8th 2008
DC1418A-B - Demo Board for:LT6604-5 - Dual Very Low Noise, Differential Amplifier and 5MHz Lowpass Filter
...
DC1418A-A - LT6604-2.5 | Dual Matched 2.5MHz 4th Order LP Filter Demo Board
Jul 8th 2008
DC1418A-A - Demo Board for:LT6604-2.5 - Dual Very Low Noise, Differential Amplifier and 2.5MHz Lowpass Filter
...
DC1147A-F - LTC6405 demo circuit
Jun 4th 2008
DC1147A-F - Demo Board for:LTC6405 - 2.7GHz, 5V, Low Noise, Rail-to-Rail Input Differential Amplifier/Driver
...
DC987B-B - LTC6400-14 3GHz Fully Differential ADC Driver Demo Circuit
May 22nd 2008
DC987B-B - Demo Board for:LTC6400-14 - 2.4GHz Low Noise, Low Distortion Differential ADC Driver for 300MHz IF
...
1.8/1.3GHz, Low Distortion, Dual ADC Drivers Deliver Guaranteed Matching & Low Noise
May 5th 2008
MILPITAS, CA - May 5, 2008 - Linear Technology announces the
LTC6420-20 and LTC6421-20, the industrys first high-speed dual
differential ADC drivers with guaranteed gain matching, and
exceptional noise and distortion performance. With guaranteed
matched gain of ±0.25dB and matched phase of ±0.1° (typ), the
LTC6420-20 reduces ...
DC987B-F - LTC6401-14 3GHz Fully Differential ADC Driver Demo Circuit
Apr 30th 2008
DC987B-F - Demo Board for:LTC6401-14 - 2GHz Low Noise, Low Distortion Differential ADC Driver for DC-140MHz
...
DC1299A-A - LTC6420CUD-20 | Dual Matched 1.8GHz Differential Amplifiers/ADC Drivers
Apr 2nd 2008
DC1299A-A - Demo Board for:LTC6420-20 - Dual Matched 1.8GHz Differential Amplifiers/ADC Drivers
...
DC1299A-B - LTC6421CUD-20 | Dual Matched 1.3GHz Differential Amplifiers/ADC Drivers
Mar 25th 2008
DC1299A-B - Demo Board for:LTC6421-20 - Dual Matched 1.3GHz Differential Amplifiers/ADC Drivers
...
DC987B-E - LTC6401-8 3GHz Fully Differential ADC Driver Demo Circuit
Feb 8th 2008
DC987B-E - Demo Board for:LTC6401-8 - 2.2GHz Low Noise, Low Distortion Differential ADC Driver for DC-140MHz
...
DC1147A-E - LTC6403-1 demo circuit
Jan 30th 2008
DC1147A-E - Demo Board for:LTC6403-1 - 200MHz, Low Noise, Low Power Fully Differential Input/Output Amplifier/Driver
...
DC987B-H - LTC6401-26 3GHz Fully Differential ADC Driver Demo Circuit
Jan 14th 2008
DC987B-H - Demo Board for:LTC6401-26 - 1.6GHz Low Noise, Low Distortion Differential ADC Driver for DC-140MHz
...
DC987B-D - LTC6400-26 3GHz Fully Differential ADC Driver Demo Circuit
Jan 14th 2008
DC987B-D - Demo Board for:LTC6400-26 - 1.9GHz Low Noise, Low Distortion Differential ADC Driver for DC-300MHz
...
DC1304A-A - LTC6602 Demo Board | Dual Programmable 900kHz LP/BP Filter / ADC Driver
Jan 3rd 2008
DC1304A-A - Demo Board for:LTC6602 - Dual Matched, High Frequency Bandpass/Lowpass Filters
...
DC1147A-B - LTC6404-2 demo circuit
Nov 16th 2007
DC1147A-B - Demo Board for:LTC6404 - 600MHz, Low Noise, High Precision Fully Differential Input/Output Amplifier/Driver
...
DC1058A-C - Combo Demoboard for LTC2207 and LTC6404-2, req. DC718
Nov 16th 2007
DC1058A-C - Demo Board for:LTC2207 - 16-Bit, 105Msps ADCLTC6404 - 600MHz, Low Noise, High Precision Fully Differential Input/Output Amplifier/Driver
...
DC1147A-A - LTC6404-1 demo circuit
Nov 16th 2007
DC1147A-A - Demo Board for:LTC6404 - 600MHz, Low Noise, High Precision Fully Differential Input/Output Amplifier/Driver
...
Loading