1. Skip to navigation
  2. Skip to content
  3. Skip to sidebar

Solutions Search - Differential Amplifiers

Converting a Low Distortion Single-Ended Sine Source to Fully Differential

Guy Hoover - Applications Engineer Sep 10th 2017
Customers looking for a way to evaluate ADCs with differential inputs will find themselves in need of a low distortion, low noise differential sine source. Single-ended sine sources can be obtained by building a simple Wien-bridge oscillator or by employing any of several readily available audio oscillators. Differential sine ...

Blog Post 


Improving Linearity by Using Absorptive Filters

Clarence Mayott - Applications Engineer Mar 10th 2017
Introduction: When driving a direct sampling high speed ADC, the most likely place to degrade the performance is the interface between the final amplifier and the ADC. With any direct sampling ADC there will be nonlinear charge produced in the sampling process. This charge is reflected into the input network each time the sampling ...

Blog Post 


High Linearity, Low Noise LTC2387-18 Drivers for Sinusoidal Signals

Doug Stuetzle - Senior Analog Applications Engineer Jan 10th 2017
Introduction The LTC2387-18 is a high speed SAR (Successive Approximation Register) ADC suited for high linearity, low noise applications. This ADC is capable of sampling at up to 15Msps, which allows it to convert signals at frequencies of several MHz. It is well-suited to convert both pulsed and continuous signals in this ...

Blog Post 


LTC2387 Drivers Part III: Trans-Impedance Amplifier/Driver

Derek Redmayne - Staff Scientist Sep 8th 2016
This is unabashedly a classic case of what marketing calls “a solution looking for a problem”. It is an example of how the full SNR of the LTC2387 may be realized for a real world signal. Most signals originating in low level circuitry, in sensors, or in the real world, will require significant gain to develop 8Vp-p ...

Blog Post 


Anti-Alias Filter for 24-bit ADC

Guy Hoover - Applications Engineer Aug 3rd 2016
For many ADC applications a simple RC filter at the buffer input will provide adequate anti-alias filtering. For applications that require a higher order filter an active filter is often used. The active component in that filter must have sufficient bandwidth, fast settling, low noise and low offset so that it doesn’t ...

Blog Post 


Baseband Design Example for LTC5589/LTC5599 Low-Power IQ Modulator

Bruce Hemp - Applications Section Leader Jul 1st 2016
Introduction This basic low power modulator was described in the LT Journal Nov 2015 article. In this blog post, we will show how to: Use simulation to validate the filter design, and Reduce DC offsets by utilizing Differential Amplifiers for the baseband drive. Also shown are some miscellaneous tips to help complete ...

Blog Post Circuit LTspice 


How to Drive the LTC2387 (Part 1): Signal Applications to 5MHz that Require Low Inter-Modulation Distortion

Derek Redmayne - Staff Scientist May 13th 2016
The biggest challenge in driving a 15Msps, 18-bit ADC with an 8Vp-p input range is the lack of integrated amplifiers with adequate bandwidth, low noise, and the required output excursion. There are low-noise, high-BW amplifiers than can produce 2VPP. There are low speed amplifiers than can produce 8VPP. For low distortion beyond ...

Blog Post 


LTspice: SAR ADC Driver Interface

Kris Lokere - Strategic Applications Manager Apr 3rd 2014
High-performance SAR ADCs can offer amazing dynamic range and linearity at faster and faster sample rates. But how do you design the amplifier and interface at the analog inputs? LTspice IV can help. This video shows how to use LTspice to simulate the analog input interface of high-performance SAR ADCs. We will look at charge ...

Blog Post Video LTspice 


Digital Gain Compression (DGC) for SAR ADCs

Mar 11th 2014
The LTC2378-20 offers a digital gain compression (DGC) feature which defines the full-scale input swing to be between 10% and 90% of the ±VREF analog input range. This feature allows the SAR ADC driver to be powered off of a single positive supply since each input swings between 0.5V and 4.5V as shown in the figure below. Needing ...

Blog Post 


Matched Resistor Networks for Precision Amplifier Applications

Tyler Hutchison - Signal Conditioning Design Engineer May 1st 2012
Introduction Some ideal op amp configurations assume that the feedback resistors exhibit perfect matching. In practice, resistor non-idealities can affect various circuit parameters such as common mode rejection ratio (CMRR), harmonic distortion and stability. For instance, as shown in Figure 1, a single-ended amplifier configured ...

Blog Post