Solutions Search - Application Specific Comparators

LT6703 AC Line Overcurrent Indicator

Philip Lane - Field Applications Engineer
Gabino Alonso - Strategic Marketing Engineer
Scott Olson - Associate Engineer Jun 4th 2016
Circuit Description This circuit design is to monitor the average current in an AC line-connected load and to illuminate an LED if it exceeds a specified level. µPower, Low Voltage Comparator with Reference The basis of this design is the LT6703-2 which combines a micropower, low voltage comparator with a 400mV reference ...

 

High Accuracy, μPower, Over-Voltage Detector with Glitch Suppressor Using LTC1541 and LTC6994

May 4th 2016
An overvoltage detector which suppresses glitches is constructed from the LTC®1541 micropower op amp + comparator + voltage reference and LTC6994-1 TimerBlox® delay block/debouncer. In this circuit, the LTC1541 comparator detects power rail overvoltage conditions (including glitches). The built-in op amp inverts this ...

 

Parameters that Affect Comparator Propagation Delay Measurements

Kevin B. Scott - Senior Strategic Marketing Engineer Nov 4th 2015
One of the key specifications for a comparator is propagation delay - the amount of time it takes for a signal propagate from the comparator input to the output. Whether as a threshold detector in a battery powered application, or on a high speed signal processing board, the comparator's propagation delay is often the first ...

 

LT6703 μPower Supply Voltage Monitor with 2V Hysteresis

Mar 17th 2015
The LT6703 µPower, low voltage comparator and reference offers a single comparator and accurate reference in a 2mm × 2mm DFN package. The -3 version is has a non-inverting input. Although only one of its comparator inputs is accessible (the other is connected to a 400mV internal precision voltage reference) its size ...

 

LTC4000 48V to 10.8V at 10A Buck Converter 3-Cell LiFePO4 Battery Charger with 2.9h Termination Timer, 1.25A Trickle Charge Current and Charging PFET Thermal Protection

Sep 23rd 2014
The LTC®4000 is a high voltage, high performance controller that converts many externally compensated DC/DC power supplies into full-featured battery chargers. ...

 

LTC2960 Micropower Power Supply Sequencer and Supervisor

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout ...

 

LTC2960 Automotive Supervisor

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout ...

 

LTC2960 Li-Ion Battery and Regulator Monitor

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout ...

 

LTC2960 Window Comparator for High Voltage Input

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout ...

 

LTC2960 Battery Disconnect to Protect Against Deep Discharge

Mar 21st 2012
The LTC®2960 is a nano-current, high voltage two-input voltage monitor, ideally suited for multicell battery applications. External resistive dividers configure custom comparator thresholds. The supervisory circuit monitors the ADJ input and pulls the RST output low when the input drops below threshold. A reset timeout ...

 

LT2940 28V Power to Frequency Converter

Nov 30th 2009
In some environments isolation is necessary for safety or noise reasons. The circuit above shows a power-to-frequency converter using the LT2940. The PMON output alternately charges and discharges a film capacitor, C5. When the voltage on C5 charges to the upper threshold on hysteretic comparator LTC1440, its output flips ...

 

DC548A - LTC1921CMS8 | Dual -48V Suppy and Fuse Monitor

May 10th 2002
DC548A - Demo Board for:LTC1921 - Dual -48V Supply and Fuse Monitor ...

 

DC600A - LTC1540CDD | Nano-power Voltage Comparator with Built In Voltage Reference in DFN Package

Jul 12th 1999
...

 

DC601A - LTC1541CDD | Micro-power Combination Op Amp, Comparator and Voltage Reference in DFN Package

Sep 22nd 1997
...

 

Pilot Light Flame Detector with Low-Battery Lockout using a Type R Thermocouple

Sep 22nd 1997
The LTC1541 combine a micropower amplifier, comparator and bandgap reference in an 8-pin package. The part operates from a single 2.5V to 12.6V or dual ±1.25V to ±6.3V supply with a typical supply current of 5µA. Both the op amp and comparator feature a common mode input voltage range that extends from the negative supply ...

 

LTC6990/LTC1440/LTC1059 Quadrature Sine Wave Oscillator

Jan 1st 1987
This circuit provides a voltage controlled frequency range from 2Hz to 18kHz with 1Vp-p constant putput amplitude. The LTC6990 is a precision silicon oscillator with a programmable frequency range of 488Hz to 2MHz. It can be used as a fixed-frequency or voltage-controlled oscillator (VCO). The LTC6990 is part of the TimerBlox ...