LTC4413 - Dual 2.6A, 2.5V to 5.5V, Ideal Diodes in 3mm × 3mm DFN


  • 2-Channel Ideal Diode ORing or Load Sharing
  • Low Loss Replacement for ORing Diodes
  • Low Forward On-Resistance (100mΩ Max at 3.6V)
  • Low Reverse Leakage Current (1μA Max)
  • Small Regulated Forward Voltage (28mV Typ)
  • 2.5V to 5.5V Operating Range
  • 2.6A Maximum Forward Current
  • Internal Current Limit and Thermal Protection
  • Slow Turn-On/Off to Protect Against Inductive Source Impedance-Induced Voltage Spiking
  • Ultralow Quiescent Current Consumption, Low Power Alternative to the LTC4413-1
  • Status Output to Indicate if Selected Channel is Conducting
  • Programmable Channel On/Off
  • Low Profile (0.75mm) 10-Lead 3mm × 3mm DFN Package

Typical Application

LTC4413 Typical Application
LTC4413 Typical Application


The LTC4413 contains two monolithic ideal diodes, each capable of supplying up to 2.6A from input voltages between 2.5V and 5.5V. Each ideal diode uses a 100mΩ P-channel MOSFET that independently connects INA to OUTA and INB to OUTB. During normal forward operation the voltage drop across each of these diodes is regulated to as low as 28mV. Quiescent current is less than 40μA for diode currents up to 1A. If either of the output voltages exceeds its respective input voltages, that MOSFET is turned off and less than 1μA of reverse current will fl ow from OUT to IN. Maximum forward current in each MOSFET is limited to a constant 2.6A and internal thermal limiting circuits protect the part during fault conditions.

Two active-high control pins independently turn off the two ideal diodes contained within the LTC4413, controlling the operation mode as described by Table 1. When the selected channel is reverse biased, or the LTC4413 is put into low power standby, a status signal indicates this condition with a low voltage.

A 9μA open-drain STAT pin is used to indicate conduction status. When terminated to a positive supply through a 470k resistor, the STAT pin can be used to indicate that the selected diode is conducting with a high voltage. This signal can also be used to drive an auxiliary P-channel MOSFET power switch to control a third alternate power source when the LTC4413 is not conducting forward current.

The LTC4413 is housed in a 10-lead DFN package.

LTC4413 Lower Iq
LTC4413-1 Lower Vfwd, Faster Response, Higher Iq
LTC4413-2 Lower Vfwd, Faster Response, Higher Iq, 13V (max) OVP


CAD Symbols and Footprints: The downloadable Zip file below contains the schematic symbol and PCB footprints.

For complete and up to date package information and drawings, please refer to our packaging page

Part Number Package Code Temp Package
LTC4413EDD#PBF 3x3 DFN-10 DD E 05-08-1699 Yes
LTC4413EDD#TRPBF 3x3 DFN-10 DD E 05-08-1699 Yes

LTC4413 Package Drawing

Order Info

  • Part numbers ending in PBF are lead free. Solder plated terminal finish (SnPb) versions are non-standard and special terms and conditions and pricing applies if available. Please contact LTC marketing for information.
  • Part numbers containing TR or TRM are shipped in tape and reel or 500 unit mini tape and reel, respectively
  • Please refer to our general ordering information or the product datasheet for more details

Package Variations and Pricing

Part Number Package Temp Price
LTC4413EDD#PBF 3x3 DFN-10 E $3.07 $2.15 Yes
LTC4413EDD#TRPBF 3x3 DFN-10 E $2.25 Yes
Buy NowRequest Samples
* The USA list pricing shown is for BUDGETARY USE ONLY, shown in United States dollars (FOB USA per unit for the stated volume), and is subject to change. International prices may differ due to local duties, taxes, fees and exchange rates. For volume-specific price or delivery quotes, please contact your local Linear Technology sales office or authorized distributor.

Demo Boards

Linear Technology offers many demo boards free of charge to qualified customers. Contact your local sales office or distributor to inquire about a demo board. Certain demo boards are also available for sale via credit card on this website. Demo boards are for evaluation purposes only. It remains the customer’s responsibility to verify proper and reliable operation in the actual end application.

Part Number Description Price Documentation
DC839A LTC4413EDD | Dual Ideal Diode-Triple Power Path Controller, Vin = 2.5-5.5V, Vout = 2.5-5.5V@2.6A MAX $100.00
Buy Now
Click here to view our complete list of demo boards


  • Battery and Wall Adapter Diode ORing in Handheld Products
  • Backup Battery Diode ORing
  • Power Switching
  • USB Peripherals
  • Uninterruptable Supplies

Product Notifications

Please login to your MyLinear account for notifications of datasheet updates, new document releases and LTspice model announcements for your favorite products. If you do not have a MyLinear account you may Sign Up Now.

Forgot your password? Click here.
Need help? Email with questions and comments.

Design Tools


LTspice® software is a powerful, fast and free simulation tool, schematic capture and waveform viewer with enhancements and models for improving the simulation of switching regulators. Click here to download LTspice

Models for the following parts are available in LTspice:

Technical Support